Recommended Trailer Hitch And Trailer Wiring For 2008 Land Rover LR2
Question:
can i use euro ball mount with Curt 13052-59146 Trailer Hitch
asked by: Pétur F
Expert Reply:
The Curt Trailer Hitch Receiver, part # C13052 is a verified as a good fit for your 2008 Land Rover.
This is a Class lll hitch and it has a 2 inch receiver opening.
The Euro ball mounts we offer are not designed for a 2 inch receiver. They fit 1-1/4 inch receiver openings.
You might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with clip, and a storage bag.
If you do not have trailer wiring I recommend the 4 Pole Harness and Hardwire Kit, part # C59496. This includes all of the hardware needed for installation, and even includes a circuit tester to help make the job easier.
You will need to use the circuit tester to locate the brake light circuit behind the vehicle tail light. This circuit will be connected to the wire coming from the converter box in the wiring kit.
Then, locate the left turn signal wire and connect the yellow wire to that wire. The green wire is then run to the passenger side and connected to the right turn signal circuit. The brown wire is connected to the tail light circuit and the white wire is connected to a clean bare metal surface on the vehicle. The power wire is run to the vehicle battery using the included inline fuse holder.
Products Referenced in This Question
etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- 1-7/8 Inch Ball
- 2 Inch Ball
- Two Balls
- Steel Ball
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Drop - 4 Inch
- Rise - 1 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Ball Mount Kit
- etrailer
more information >
Curt Powered Tail Light Converter w/ 4-Way Flat Trailer Connector and Install Kit
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- 8 Feet Long
- Universal Fit
- 4 Flat
- CURT
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 400 lbs TW
- 4000 lbs GTW
- 2 Inch Hitch
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Q&A: What is the Difference Between 7-Way RV and Utility Trailer Connectors
- Q&A: Recommended RV Exterior Ladder for 22 Ft Thor Four Winds RV
- Q&A: Why Is 5th Wheel Trailer Clunking When Starting/Stopping with B&W Companion and MORryde Pin Box
- Q&A: Troubleshooting A Clunking Noise Between A Fifth Wheel Hitch And Base Rails While Towing
- Q&A: Trailer Hitch for a 2015 Honda Pilot
- Q&A: Parts Needed to Tow a Trailer with a 2015 Honda Pilot
- Q&A: Installation of Hitch on Fifth Wheel Trailer
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Best Bike Racks for Electric Bikes
- Article: How to Choose the Right Trailer Hitch Class
- Article: Trailer Hitch Receiver Sizes
- Article: My Trailer Hitch Doesn't Fit
- Article: How to Measure for Trailer Hitch Drop