Will BOLT Trailer Hitch Receiver Lock Code to 2014 Chevy Suburban's Ignition Key

Question

Question:

So this will work for my 2014 Chevy Suburban??

asked by: Arthur

0

Expert Reply:

I spoke with my contact at BOLT and he confirmed that the BOLT Trailer Hitch Receiver Lock for 2" and 2-1/2" Hitches, part # BL7018446, will code to your 2014 Chevy Suburban's ignition key. This lock is a great alternative to a standard pin and clip to prevent theft of your ball mount or hitch-mounted accessories.

expert reply by: Chris O

0

Answer 1

The useable span on Curt hitch lock #C23519 is 3-5/8 inches so it will work great on your 2016 Chevy Suburban with the factory 2 inch trailer hitch. And like you said it is stainless steel so corrosion will not be a factor. I have linked a video…

view full answer...

Answer 2

Are you sure you need a span that large? Typically a 2 inch hitch like what you have wouldn't require nearly as much as that. For example the Curt hitch lock part #C23519 (which is an excellent choice for a hitch lock has a span of 3-5/8 inches…

view full answer...

Answer 3

One of the nicer locking hitch pins we offer is the Curt #C23519. This 5/8-inch diameter hitch pin will work with 2-inch and 2-1/2 inch hitch receiver tubes. It is made of stainless steel and also includes a waterproof cap to keep dust out. This…

view full answer...

Answer 4

Yes the Trailer Hitch Receiver Lock part #C23519, is for 2 inch trailer hitch receivers. The link below will take you to all the locks that will work with the 2-1/2 inch receivers.

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 10

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Will BOLT Trailer Hitch Receiver Lock Code to 2014 Chevy Suburban's Ignition Key

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching