Thule Evolution 1600XT Roof Box Replacement Carriage Bolt and Knob

Question

Question:

I have a Thule Evolution 1600XT and need some replacement hardware. Specifically I need the carriage bolt part number 10403 and knob part number 04877. I was not able to find them on the site. Do you carry them or have a replacement suggestion? Thank you.

asked by: Andrew G

0

Expert Reply:

The bolt you need is the part # TH10403 that you referenced. The part number for the knob you need is the part # TH04877.

expert reply by: Jameson C

0

Answer 1

The 123 on your tire is for the load index. The load for this tire is 3417 lbs. The L is the speed rating. For your tire, the speed rating is 75 mph. The load range indicates the horizontal and sidewall strength, measured using ply rating and load…

view full answer...

Answer 2

Your Thule Evolution 1600 6410 cargo box used the EasySnap Mounting Hardware Kit, which is now obsolete. Therefore, your best and closest option is to use the Replacement QM3 - Quick Mount Hardware #TH04997 to attach the box to your Malone AirFlow2…

view full answer...

Answer 3

I may have a solution for you, but there is not a U-bolt available from Thule that is 3-1/2" wide by 3" deep. The closest option available is the Replacement U-Bolt for Thule Trail Large and Medium Cargo Baskets #1500052553 that is…

view full answer...

Answer 4

The closest thing we offer to what you are looking for is the Replacement Carriage Bolt #TH915-0675-11 which is a M6 Carriage bolt that is 75mm.

view full answer...

Answer 5

I do not have a specific set of instructions for the Thule QM3 Quick On-Off Mounting Hardware Kit, item #TH04997, but I did come up with a drawing, see attached, that shows exactly how the parts of the kit install.

view full answer...

Answer 6

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...