How Tall is the Ball Part of B&W Gooseneck Ball GNXA2000

Question

Question:

From bed how tall is ball on turnover ball for 2005 superduty

asked by: Kent

0

Expert Reply:

I went out to our warehouse and pulled B&W gooseneck ball # BWGNXA2000 to measure the height of the ball portion. It is approximately 4-1/6 inches from the square base to the top of the ball.

expert reply by: Michael H

0

click to enlarge

Answer 1

The B&W Ball and Safety Chain Kit #BWGNXA2062 will sit 5-3/4" above the gooseneck ball hole on your 2020 Ram 3500. You will need to add or subtract any difference in the bed height from the top of the bed rails to the top of the gooseneck…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

Hey Richard, thanks for reaching out! The Air Lift LoadLifter 7500 XL Air Helper Springs #AL57541 does take up the same space as the Curt 19419346 5th wheel bracket kit for your 2024 GMC Sierra 3500. The only way to remedy this is to use the…

view full answer...

Answer 4

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower the…

view full answer...

Answer 9

For your 2015 GMC Sierra 3500 Denali DRW 4x4, I recommend using the Firestone Ride-Rite Red Label Extreme Duty Air Helper Springs part #F2709 over the Air Lift LoadLifter 7500 XL Air Helper Springs part #AL57538 for two reasons. The first reason is…

view full answer...

Answer 10

If you are considering Timbrens like the #TDR1500DQ and the SumoSprings like the #SSR-307-47 for your 2022 Ram 1500 4x4, I recommend the SumoSprings #SSR-307-47. The SumoSprings will offer the same quality as the Timbrens in terms of suspension…

view full answer...

Answer 11

When installing the Roadmaster Split Bushing for Anti-Sway Bar part #RM-205249-10, I recommend using the Mystik JT-6 part #L74FR. This is a marine grease that is very similar to what comes with their sway bars.

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

How Tall is the Ball Part of B&W Gooseneck Ball GNXA2000

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching