Availability Of Trailer Tongue Weight Scale

Question

Question:

The only tongue weight scale I can find doing a search on your website is the one Sherline 2000. Is that the only one you sell?

asked by: Dave M

0

Expert Reply:

The etrailer Trailer Tongue Weight Scale, part # e99044 is the only tongue weight scale we offer.

This scale has an easy-to-read gauge that shows the weight in both pounds and kilograms and has a capacity of 2,000 lbs. I have attached a product review video you can check out.

expert reply by: Jeffrey L

0

Answer 1

Both the Sherline Trailer Tongue Weight Scale #5780, and the etrailer Tongue Weight Scale #e99044 will accurately measure the tongue weight on your trailer as long as the tongue weight is less than 2000lbs. With that said I prefer the etrailer…

view full answer...

Answer 2

I can help you determine the tongue weight of your trailer with the Hensley Hitch and Stinger attached. I would recommend you place the etrailer #e99044 scale under the jack foot to measure your tongue weight. You will want to make sure the trailer…

view full answer...

Answer 3

The center of the ball on the plate that mounts on the trailer should be 24 inches from the center of the trailer coupler (where the center of the hitch ball would be when towing). The first two diagrams on the top of page 2 in the instructions (see…

view full answer...

Answer 4

The sticker you are looking at on the etrailer Tongue Weight Scale for Campers and Utility Trailers - 2,000-lb Capacity #e99044 can be ignored. This is for the installation of the gauge, but the gauge already comes installed. The only thing you need…

view full answer...

Answer 5

The Sway Control Kit #83660 can be welded but is not necessary. A drill would be required for the self tapping screws that are included with this kit. If you don't have the sway ball mount for your receiver I recommend our Sway-Control Bracket…

view full answer...

Answer 6

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 7

Weight distribution works to distribute the tongue weight of a trailer up to the front axle of the tow vehicle so that it will sit more level and handle/brake better. That being said the systems do not "reduce" tongue weight or allow you to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Availability Of Trailer Tongue Weight Scale

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching