How to Install Lippert Bolt-On Shock Mount Kit with Heavy Duty Gas Shocks for 3 Inch Axles
Question:
Hi, could you tell me how these are installed?
asked by: Laura
Expert Reply:
I will be happy to explain how to install the shock kit # LC281281. In addition to the instructions below I have also included a picture of the actual instructions.
1. Raise trailer and jack up the axle to release pressure on the springs.
2. Remove old u-bolts and tie plate.
3. Install new tie plate with the longer side facing outward and torque the u-bolts to the specs in the instructions. NOTE: Do NOT reuse old components.
4. Compress the shock and make a mark on the inner shock where the outer shock stops.
5. Release compression. Measure the stroke and make a mark on the inner shock that is one half of the stroke length.
6. Measure the shock length when the shock is compressed to the halfway mark made in Step 5.
7. Lower the trailer back down onto tires and level so the equalizer(s), if equipped, are parallel to the frame and there is a full load on the springs.
8. Make a measurement perpendicular to the shock mounting lip on the tie plate that is the same distance measured in Step 6 + 2” and make a mark on the I-beam parallel to the shock mounting lip on the tie plate. NOTE: Mount shocks pointing outwards (away from the shackle kit, equalizer and/or center point) to get the best performance from the shocks. NOTE: Dry fit the shock to be sure it does not exceed a 45 degree angle or it will not function.
9. Align the bottom of the extended portion of the upper shock mounting bracket to the mark made on the I-beam in Step 8 and drill 11/32” pilot holes.
10. Use the 3/8” self-tapping bolts to secure the upper shock mounting bracket to the I-beam.
11. Remove nut, washer and rubber grommet from both sides of the shock.
12. Place the shock into the shock mounting lip on the tie plate and compress it to fit into the upper mounting bracket.
13. Apply the rubber grommet, washer, and nut (in that order) and tighten to secure the shock.
NOTE: Do NOT over-tighten. Tighten until the rubber grommet increases diameter equal to the washer.
Al
7/24/2020
I purchased lc281281 universal sHock kit ,was getting ready to drill my trailer i beam and my neighbor engineer said are you sure you are supposed to drill that i beam? Wont it severly weaken it? Now i am not sure what todo? Any help or reassurance please.
Chris R.
7/29/2020
Product Page this Question was Asked From
Lippert Bolt-On Shock Kit w/ Heavy Duty Gas Shocks - 5,200-lb to 7,000-lb (3") Overslung Axle
- Trailer Leaf Spring Suspension
- Leaf Spring Enhancement System
- Boat Trailer
- Camper
- Car Hauler
- Snowmobile Trailer
- Utility Trailer
- Shocks
- Round Axle - 3 Inch
- Single Axle
- Lippert
more information >
Continue Researching
- Shop: Lippert Bolt-On Shock Kit w/ Heavy Duty Gas Shocks - 5,200-lb to 7,000-lb (3") Overslung Axle
- Shop: Lippert Bolt-On Shock Kit w/ Heavy Duty Gas Shocks - 3,500-lb (2-3/8") Axle
- Shop: Lippert Heavy-Duty Replacement Shock - Yellow
- Video: Lippert Components Trailer Suspension LC283280 Review
- Video: Review of Lippert Components Trailer Leaf Spring Suspension - Springs - LC281281
- Video: Review of Lippert Trailer Leaf Spring Suspension - Bolt-On Shock Mount Kit - LC281255
- Shop: Replacement Upper Mounting Bracket for Lippert Gas Shock Kit - Qty 1
- Video: Roadmaster Comfort Ride Shock Absorbers Installation - 2017 Grand Design Solitude Fifth Wheel
- Q&A: How to Measure for Adding Lippert Bolt-On Shock Kit for 3 Inch Axles to Trailer
- Shop: Roadmaster Comfort Ride Add-On Kit for Triple Axle Trailers - 5,200-lb to 7,000-lb Axles
- Q&A: Can Trailers Have Shock Absorbers Installed
- Shop: Roadmaster Comfort Ride Shock Absorbers for Tandem Axle Trailers - 8,000-lb Axle
- Shop: Lippert Standard Replacement Shock - Black
- Q&A: How to Measure to Determine Fit of Lippert Bolt-On Shock Kit LC281281
- Q&A: Installation of Lippert RV Shocks Kit # LC281281
- Search Results: axle stabilizer
- Video: B and W Companion Slider Gooseneck-to-5th-Wheel Trailer Hitch Adapter Installation - 2019 Ford F-250
- Q&A: Recommended Shock Absorbers On 5th Wheel Trailer For More Comfortable Towing Experience
- Q&A: Correct Shocks for a 2022 Jayco Eagle Fifth Wheel 321RSTS
- Shop: Suspension Enhancement
- Search Results: shackle straps
- Q&A: How to Install Lippert Bolt-On Shock Mount Kit with Heavy Duty Gas Shocks for 2-3/8 Inch Axles
- Video: Lippert Center Point Trailair Air-Ride Suspension Upgrade Review
- Search Results: shock absorber
- Search Results: shock kit
- Video: Lippert Road Armor Shock Absorbing Equalizer Kit Installation - 2022 Grand Design Imagine Travel Tra
- Search Results: disc brake conversion kit
- Shop: Trailer Wiring
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Transmission Cooler
on Trailer Leaf Spring Suspension
Al
7/29/2020
Thanks for the input, full steam ahead