Overall Dimension Of Brophy Trailer D-Ring Tie Down

Question

Question:

What is the width of the D-ring?

asked by: Garry

0

Expert Reply:

I have attached a photo of the Brophy Trailer D-Ring Tie Down, part # SR15-C with the dimensions all noted.

The overall dimension of the D-ring is 2-1/4 inches and the inside width of the D-ring is 1-1/2 inches.

expert reply by: Jeffrey L

0

click to enlarge

Answer 1

When installing the Brophy Trailer D-Ring Tie Down, part #SR15-C, you will need a 3/8 inch carriage bolt. The square underside of the carriage bolt will fit inside the mounting holes of the tie down. I have attached a photo of the SR15-C with the…

view full answer...

Answer 2

The Brophy Trailer D-Ring Tie Down, part #SR15-C, does not include any mounting bolts. I went out in the warehouse and measured the size of the holes for mounting and they measured 7/16 inch x 7/16 inch. So you will want to use something smaller…

view full answer...

Answer 3

What you have heard is correct, you do not want to mount tie downs to the wood floor of a trailer without any type of reinforcement. The tie down will only be as strong as the weakest component and the wood floor of a trailer would be the weakest…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 9

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 10

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 11

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 12

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Overall Dimension Of Brophy Trailer D-Ring Tie Down

Product Page this Question was Asked From

Continue Researching