What Do I Need to Tow a Motorcycle Trailer with a 2007 Hyundai Sonata
Question:
I have a 2007 Hyundai Sonata, I want to get a trailor hitch to tow a motorcycle using a motorcycle trailor. What ALL do I need to purchase?
asked by: Tess
Expert Reply:
The components needed to tow a trailer include a trailer hitch receiver, ball mount, pin and clip, trailer hitch ball, and a wiring harness. I have included an article which covers this.
To get your 2007 Hyundai Sonata ready for towing, I recommend the following:
Trailer Hitch - Draw-Tite Class I Trailer Hitch Receiver, # 24757. This is a custom fit hitch offering a 2,000 lb towing capacity and bolt-on installation. No drilling or welding is required.
Ball Mount - Sportframe Drawbar, # 3592.
Pin and Clip - Included with part # 3592.
Hitch Ball - # 19258 for 2 inch or # 19256 for 1-7/8 inch.
Wiring Harness - T-One Vehicle Wiring Harness, # 118433, if your vehicle isn't already equipped with a 4 way trailer connector.
I have included a couple installation videos for you to check out.
I always like to remind everyone to check your owner's manual to determine the towing capacity of their vehicle before towing. You are always limited by the lowest rated component in your towing setup.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
1-7/8" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
2" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
Draw-Tite Drawbar for 1-1/4" Hitch - 2-1/8" Rise, 2-3/4" Drop - 9-3/4" Long - 2K
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 1-1/4 Inch Hitch
- 2000 lbs GTW
- Class I
- Draw-Tite
more information >
Product Page this Question was Asked From
Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Upgrading Trailer Tires and Wheels For Highway use on Harbor Freight 4x8 Folding Trailer
- Article: The 5 Best Trailer Drop Hitches You Can Buy
- Q&A: Troubleshooting Featured Disabled Code With Lippert Ground Control 3.0
- Q&A: What is the Difference Between Class 1 and Class 2 Hitches for the Scion XB
- Q&A: Explanation of Why Class II Hitch Cargo Carrier Wont Fit Class I Hitch
- Q&A: Is There Replacement Mounting Hardware for the Fairing on Curt Roof Mounted Cargo Basket # 18115
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Difference Between Hydrastar Brake Kits for Tandem 7k Axles HSE7K-T1 and HSE7K-T1SO
- Article: Best Bike Racks for Electric Bikes
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Does the Kuat NV 2.0 Work with Bikes with Fenders?