How to Use a Pullrite Superglide 4400 on a 2015 Ram 2500 with Hitch Prep

Question

Question:

Will this picture frame rail mount kit work with my pull rite 20k super glide hitch?product number is 4400

asked by: Wes

0

Expert Reply:

The PullRite 4400 part number you referenced is the Superglide hitch that is designed only to fit Pullrite rails. In order to use this hitch on industry standard rails you would need the Pullrite part number 4409 which we don't carry.

With that adapter you could use the picture frame adapter for Mopar rail kits part # RP30154 that you referenced.

expert reply by: Jameson C

0

Answer 1

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 4

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 5

So for your set up, a 2021 Ram 2500 short bed with the RamBoxes, you will need to use a Sidewinder in order to have the clearance to tow a 5th wheel. The Goose Box doesn't move the pivot point and an offset ball just won't be enough for…

view full answer...

Answer 6

Most fifth wheel rails are made to the same industry standard dimensions. They aren't all though. If you measure 22 inches on center between the two rails and they look like the rails of the #RP30035 that you referenced they would be the industry…

view full answer...

Answer 7

Hey Jay. It sounds like you are on the right track here because a sidewinder pin box will be your only option for pulling your 5th wheel since you have a short bed truck with the Rambox. That said, you are right that the Reese Sidewinder cannot be…

view full answer...

Answer 8

There is a way to to a fifth wheel trailer with your 2020 Ram 2500 that has the Ramboxes but you have to install a Sidewinder pin box on the trailer so that the pivot point is raised up high enough that there isn't interference between the pin…

view full answer...

Answer 9

The Patriot Slider part #BWRVK3270 might be a bit more noisy than the Companion slider part #BWRVK3400 due to the increased number of mounting points, 4 at the corners vs. 1 in the center. Probably not that noticeable and certainly not something…

view full answer...

Answer 10

As long as the RBW Lil' Rocker mounts to industry standard base rails you'll need the Curt Adapter Rails #C29BR that fit in the OEM puck system on your 2019 Ram 2500 and give you a standard base rail connection. I'm attaching a photo…

view full answer...

Answer 11

To get the B&W Patriot #BWRVK3200 to work with your 2006 Dodge Ram you're going to need a set of 5th wheel rails #DM8552016-71. These rails are custom fit to your vehicle so they'll just bolt right up to the frame. It is worth mentioning…

view full answer...

Answer 12

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

How to Use a Pullrite Superglide 4400 on a 2015 Ram 2500 with Hitch Prep

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching