Connection 12 Volt Power Wire for 7-Way on a 2009 Dodge Journey
Question:
Hello I have a 7 pin plug on my tent trailer I want to install wiring on a vehicle for the trailer I have done all of the but the aberration charge wire where in the vehicle do I plug this to? And what do I need
asked by: Ross
Expert Reply:
Whether you are talking about the 12 volt power wire from a 4-Way powered converter or the 12 volt circuit from a 4- to 7-Way adapter, such as # 37185, they both connect to the vehicle positive battery terminal.
It sounds like you are talking about the 7-Way so for it you will need a 40 amp circuit breaker, # PK54540, and enough wire, # 12-1-1, to reach from the front of the vehicle to the rear. You would change the number in the quantity box on the wire page to the amount of feet needed. I recommend 25 feet because its better to have too much than not enough.
There should be a black wire if using a 4- to 7-Way adapter. Otherwise the 12 volt circuit is in the 11 o'clock position at the BACK of a 7-Way where the wires attach. One end of the 12-1-1 wire attaches to that black wire or in that 11 o'clock position.
Then you will route the wire under the vehicle, avoiding areas that may pinch or burn the wire such as exhaust and suspension components. Route it up through the engine compartment to the vehicle battery. The wire will connect to the AUX post of the circuit breaker. Then using left over wire attach one end to the BAT post and the other to the positive battery cable.
I also recommend wiring kit # HM51020 which comes with various connectors, ring terminals, clips, ties, and tools that you will need.
Products Referenced in This Question
Adapter 4-Pole to 7-Pole and 4-Pole
- Trailer Wiring
- Wiring Adapters
- Multi-Function Adapter
- 4 Flat
- Plug and Lead
- 4 Flat
- 7 Round - Blade
- Hopkins
more information >
Hopkins Deluxe Trailer Wiring Installation Kit
- Wiring
- Tools for Wiring
- Wiring Kits
- Installation Kit
- Hopkins
more information >
Pollak Circuit Breaker - Cycling/Automatic Reset - 40 Amp - Straight Mount Bracket
- Accessories and Parts
- Wiring
- Circuit Breaker
- 40 Amp
- Pollak
more information >
Product Page this Question was Asked From
Miro-Flex LED Clearance or Side Marker Light w/ Chrome Bezel - Submersible - 3 Diodes - Red Lens
- Trailer Lights
- Clearance Lights
- Rear Clearance
- Side Marker
- Oval
- Surface Mount
- Submersible Lights
- LED Light
- 4-3/16L x 1-3/8W Inch
- Red
- Optronics
more information >
Continue Researching
- Q&A: What is Difference Between Furrion and Voyager Observation Pre-Wiring
- Q&A: Replacement Remote For a HappiJac Electric Camper Jack System
- Q&A: Replacement LED Top Command Clearance Light With SAE-AP2-16 On Lens For 2018 Sunseeker Motorhome
- Q&A: Replacement For Furrion FOS48TAPK-BL Back Up Camera
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Wiring An Atwood RV Water Heater With Double-Panel On/Off Switch
- Q&A: Replacing Peterson PM130 Incandescent Trailer Lights with LED Versions
- Article: Trailer Lighting Requirements
- Article: Trailer Wiring Diagrams
- Q&A: Replacement Trailer Tires Size 7.50-16LT Load Range F
- Article: Double-Eye Trailer Suspension System Review
- Article: Replacing RV Awning Fabric: Your Step-by-Step DIY Guide
- Article: Testing Trailer Brake Magnets for Proper Function
- Article: Best Ladder Racks