Replacement Ladder Hardware for Surco RV Bunk Ladder # SP502B

Question

Question:

do you have replacement hooks for the broken one on my ladder

asked by: Ted M

0

Expert Reply:

Thank you for including a photo of your ladder's broken hook. We can help you!

We offer a Replacement Installation Hardware Kit # 2460 that works with Stromberg Carlson and other brands of RV ladders. You will notice that the shape of the larger hooks is slightly different than your original ones but these will work fine for you. You'll want to retain your original hardware to install them.

expert reply by: Adam R

0

click to enlarge

Answer 1

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 2

On equalizer 013-105-04 in kit #K71-360-00 the eye center to eye center measurement is approximately 7-1/2 inches.

view full answer...

Answer 3

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 4

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 5

Most likely the new axle has self-adjusting brakes which when new are known for feeling pretty weak. The good news is that you can keep applying them over and over while the trailer is traveling and they will tighten and get more sensitive feeling.

view full answer...

Answer 6

Actually on brake magnets for trailers either wire can be used as the power or the ground so the colors don't really mean anything. Most likely the magnet manufacturer just put what ever color was most convenient on your trailer.

view full answer...

Answer 7

The Tow Ready wiring harness #118571 is rated for 7.5 amps for brake lights and turn signals and 7.5 amps total for running lights. The fuse that goes on the power wire connection to the battery is a 10 amp fuse. The wire gauge of the long 12 volt…

view full answer...

Answer 8

Actually our etrailer.com brand brake assemblies are rebranded AxleTek assemblies. So we have the 8k left and right assembly set #AKEBRK-8 which is most likely what you need but these are 12-1/4 inch in diameter by 3-3/8 inches wide and attach with a…

view full answer...

Answer 9

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 10

If you need 18 feet of E-track I recommend using 2 pieces of 8 feet Horizontal E-track part #E19135 and 1 piece of 2 feet E-Track part #EM59150. 8 feet is the longest Horizontal E-Track available. The E-track pieces are not designed to be mounted…

view full answer...

Answer 11

I cannot determine which rear bumper that you have from your picture so I will give you to options based on which bumper you have on your 1989 Chevrolet K3500 Crew Cab Pickup with the 8' bed. The Draw-Tite Ultra Frame Trailer Hitch Receiver…

view full answer...

Answer 12

From your question it sounds to me like someone has cut off the tow package plug on your 2005 Ford F-150 and wired in a 4-way connector. In this case you could use the Hopkins Adapter 4-Pole to 7-Pole and 4-Pole, #37185 which will give you a 4-way…

view full answer...

Replacement Ladder Hardware for Surco RV Bunk Ladder # SP502B

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching