Replacement Handle and Gears for a 1,600 Pound Fulton F2 Dual Wheel Trailer Jack

Question

Question:

I need the handle and pins for the double wheel 1600 pound fulton jack. Sid winder. Where can I order the parts from.

asked by: Craig

1

Helpful Expert Reply:

For your 1,600 pound Fulton F2 jack # F1413050334 (or similar 1,600 pound model) the correct handle is # F500134.

expert reply by: Michael H

1

Answer 1

I went into our warehouse with a digital caliper to take the requested measurements for you. The Replacement Gear Kit for etrailer and Ram Sidewind Jacks - 2,000 lbs and 5,000 lbs #TJA-2000S-GR has an inner diameter of 0.5 inches and outer diameter…

view full answer...

Answer 2

Based on the 1-1/8" diameter x 1/2" thick measurements you provided of your current gears, the Replacement Fulton Gear Kit #F0933302S00 would be the correct gear kit for your older Fulton jack as it includes two bevel gears that are…

view full answer...

Answer 3

The Replacement Gear Kit for etrailer and Ram Round Swivel Marine Jacks part #MJ-1000B-GR have a 1/2" inner diameter and 1-1/8" outer diameter.

view full answer...

Answer 4

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 5

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 6

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 10

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Replacement Handle and Gears for a 1,600 Pound Fulton F2 Dual Wheel Trailer Jack

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching