How Does Wire Attach to Pollak Single-Pole, Round Pin Trailer Wiring Socket

Question

Question:

Hello, Ive purchased the single pole connectors in the past and always have a difficult time attaching the wire. Are there directions or an additional kit available to assist? Thank you,

asked by: Matt

0

Expert Reply:

Single pole trailer connector # PK11851 accepts such large gauge wire that a set screw could work for holding the wire in place inside the connector. But it is designed so that you can solder the wire in. You can get a soldering iron kit fairly inexpensively just about anywhere that sells tools and/or craft supplies.

expert reply by: Michael H

0

Answer 1

First thing to try is soaking the hitch ball in as much WD-40 that you can so that you can hopefully free it up. Let it sit overnight and maybe hit it with a rubber mallet as well. The next thing you can try is putting the weight of a gooseneck…

view full answer...

Answer 2

It sounds to me like you are wanting to power the dump trailer directly from your trucks battery. If this is the case you will want to start by making sure that the power draw for the lift would not overload the truck. If all looks good, you could…

view full answer...

Answer 3

If you are looking for something to power the dump on your dump trailer, I highly recommend an independent battery specifically for powering the dump trailer. We have a few different options for charging the battery on the dump trailer. Powering the…

view full answer...

Answer 4

The Bulldog Winch Quick Connects, #BDW20133, that you referenced will work to provide a quick disconnect on your custom audio trailer. These connects were designed to provide power to an electric winch, but you could also use them to provide power to…

view full answer...

Answer 5

The 00 Gauge wire you have will need to get soldered to the the Pollak Single Pole Connector #PK11852. You will remove the front portion of the connector by removing the screw on the front portion of the connector and then pulling the front part of…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

How Does Wire Attach to Pollak Single-Pole, Round Pin Trailer Wiring Socket

Product Page this Question was Asked From

Continue Researching