Dimensions of the "Junior" Non-Locking Steel Flush Door Latch # N1980

Question

Question:

What are the overall dimensions of the latch?

asked by: Nic

1

Helpful Expert Reply:

I went out into our warehouse to measure the "Junior" Non-Locking Steel Flush Door Latch # N1980 and found that overall it is 4-1/2 inches long, 3-3/4 inches wide and 1-1/2 inches deep.

expert reply by: Jameson C

1

click to enlarge

Answer 1

There is an indention in the bracket over the latch on the "Junior" Non-Locking Steel Flush Door Latch #N1980 which keeps it from falling out. I have pointed this out in the attached photo.

view full answer...

Answer 2

The "Junior" Non-Locking Steel Flush Door Latch #N1980 can be welded in place or you can drill the flange for installation with screws as you stated or rivets. If you want predrilled holes and a lock you can use the "Junior"…

view full answer...

Answer 3

I spoke to my contact at Redline and he informed me that the maximum thickness for the panel that you could install this Junior Door Latch #N1980 on would be 3/4 of an inch. Basically, this and the Full Size Door Latch #N3980 that you referenced have…

view full answer...

Answer 4

To install the handle will require you to drill holes along the lip of the door latch. I went out to our warehouse to get the dimension you are looking for and found that when the latch is pulled up it will stick up 1 inch above the housing.

view full answer...

Answer 5

I spoke with the manufacturer and they told me the depth of this door latch, product #L3980, from the recessed area to the housing area is 1 inch. The depth from top of the latch to the bottom is 1-3/4 inches. This door latch mounts in 3-3/8 inch x…

view full answer...

Answer 6

I have a solution for you, but the "Junior" Locking Stainless Steel Flush Door Latch with Inside Release #L1833 that you referenced can only fit doors up to 7/8 of an inch in thickness. For your 1 inch thick door you would want the Full…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Dimensions of the "Junior" Non-Locking Steel Flush Door Latch # N1980

Product Page this Question was Asked From

Continue Researching