Dimensions of the Brophy Aluminum Scissor Steps Part AS04

Question

Question:

Hy there. Thanks for information. You have the same step also in aluminum. And whats the wheigt and package size of them ?

asked by: Willi

0

Expert Reply:

The shipping weight for the Brophy aluminum scissor steps # AS04 is 20.72 pounds. The step size is 18 inches x 6 inches deep and vertical height measures between 31 and 39 inches high. These steps have a weight capacity of 250 pounds.

The weight capacity is the main difference between the Brophy steps # AS04 and # SS04 as the steel steps will have a 300 pound weight capacity.

The dimensions of the box they are shipped in are 17-1/8 inches height by 18-3/4 inches width by 9-3/4 deep.

expert reply by: Chris B

0

Answer 1

Realistically it is best to stick with a Dometic replacement thermostat for your Dometic setup. The #DMC79FR is the correct replacement for your 3316410.012. It may be possible to use a universal thermostat like the #CAM09221 you looked at but this…

view full answer...

Answer 2

I contacted the manufacturer regarding the installation of the Replacement Single Zone Thermostat for Dometic RV Air Conditioners #DMC79FR. They were able to provide me with a wiring diagram which I have included here for you.

view full answer...

Answer 3

The Brophy Scissors Steps part #SS04 are only to be used while vehicle is stationary. They are not made to be permanently mounted to the camper. It needs to be installed using the mounting bracket that attaches to the camper. With the mounting…

view full answer...

Answer 4

The Brophy Camper Scissor Steps - 4 Steps in aluminum, #AS04 has a shipping weight of 21 lbs. The Brophy Camper Scissor Steps - 4 Steps - Steel, #SS04 is 34 lbs.

view full answer...

Answer 5

The only digital thermostat we offer for Dometic RV Air Conditioners is the Replacement Single Zone Thermostat for Dometic RV Air Conditioners part #DMC79FR. If you feel yours is defective or not working properly then you can replace this using the…

view full answer...

Answer 6

The weight capacity of the Aluminum Scissor Steps, item #AS24, is 300 pounds.

view full answer...

Answer 7

I checked with Brophy and the folded dimensions of the scissor steps part #AS24 are 25" x 17" x 13".

view full answer...

Answer 8

Given that the mount of the Torklift #TLA7844 is 2-1/2 inches wider than the available spot on the landing, these particular steps wouldn't be the best choice. CR Brophy makes a narrower 4 step unit, part #AS04 that would be a better choice. This…

view full answer...

Answer 9

The TorkLift GlowStep Revolution Scissor Steps with Landing Gear #TLA8004 weighs 55 lbs. These particular steps fit an entry height of 32-1/2" to 44" and the steps themselves are 22" wide x 8" deep to ensure plenty of footing.…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Dimensions of the Brophy Aluminum Scissor Steps Part AS04

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching