How To Adjust And Test Electric Brakes On A Trailer

Question

Question:

On my trailer the back axel on the driver side brake is locked up. All the other brakes function perfectly. How do I unlock the brakes and fix it so that it works correctly?

asked by: Brian L

0

Expert Reply:

It sounds like you need to adjust the brake on your trailer. If you have electric brakes like the Dexter Electric Brake Assembly LH, part # 23-438, you can make the adjustments pretty easily.

I have attached a video that shows trailer brakes being installed. If you go to about the 4:40 mark on the video it shows how to adjust the brakes. I have also attached a photo of an electric brake that shows where the adjustment wheel is located.

You can also test the magnet on the brake that is giving you problems. I have attached a helpful article that explains how to test the magnets for proper function you can check out.

expert reply by: Jeffrey L

0

click to enlarge

Answer 1

A slight voltage drop between the controller and the magnets is normal. But you will need around 12 volts at the magnets for proper operation. The only way to know the wire gauge is to strip away the insulation and measure just he copper strands.…

view full answer...

Answer 2

If you are only getting 1.5 volts at your brakes then there is an issue, but there is not a fuse that controls the brakes. There are a number of possible issues so you will need to find out if the issue is on the brake controller, truck, or…

view full answer...

Answer 3

This could be a magnet wiring problem. It is unlikely that the magnets are bad on newer assemblies, but if the wiring is not properly connected, it could cause problems. Check to see that the magnets are properly grounded to a clean, bare metal…

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 7

Your math is correct in your trailer weight load example. If a fully-loaded tandem axle trailer weighs 4000-lbs then each of the 4 tires will bear 1/4th of that load, or 1000-lbs. In this case a tire rated for 1300-lbs would provide a good safety…

view full answer...

Answer 8

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is…

view full answer...

Answer 9

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...