Recommended 48 Inch Extension For RV Ladder

Question

Question:

Extension for RV ladder

asked by: James G

0

Expert Reply:

Looks like you are interested in a ladder rack extension for your RV.

The Stromberg Carlson RV Ladder Extension, part # LA-148 adds an additional 48 inches of length to your RV ladder. It is a simply no-tool installation by using the included rubber straps and attaching them to a 1 inch diameter vertical supports. This is 48 inches long and 14 inches wide and has a weight capacity of 300 lbs.

expert reply by: Jeffrey L

0

Answer 1

I do have a solution for you, but unfortunately we do not have any ladders that measure 115" by themselves. Instead what you can do is install the Stromberg Carlson RV Exterior Ladder #LA-401 which is 99-1/2" tall and then use the…

view full answer...

Answer 2

There is a ladder extension that is going to work for you so long as the vertical supports of the current ladder on your 2010 Navion 24A are 1" diameter. Ladder Extension #LA-148 is not folding but instead has rubber straps which you wrap…

view full answer...

Answer 3

The Stromberg Carlson RV Ladder Extension #LA-148 would need to be removed and stored when not in use on your coach. You really can store it anywhere; either inside the coach in a closet or in one of the storage cabins underneath. This extension…

view full answer...

Answer 4

We only have one RV exterior ladder available in black and that is the Stromberg Carlson RV Exterior Ladder w/ Hinges #LA-401BA. The Stromberg Carlson RV Exterior Ladder w/ Hinges #LA-401BA is a universal RV ladder that can be attached to an RV with…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 10

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 11

You are going to want the Master Lock Hitch Receiver and Coupler Latch Lock Set #1481DAT as it has an adjustable coupler lock which fits multiple coupler latch sizes. This like the etrailer Hitch Receiver and Coupler Lock Set #e99039 you found will…

view full answer...

Answer 12

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...

Recommended 48 Inch Extension For RV Ladder

Product Page this Question was Asked From

Continue Researching