How Far Out is the Platform from Hitch Pin Hole on Curt Hitch Mount Step 31001

Question

Question:

What is the distance from the pin to the edge of the standing platform for front mounted receivers that are tucked up under a bumper such as the curt on a 2010 F-150?

asked by: Lloyd

0

Expert Reply:

I spoke with my contact at Curt and he said that from the center of the hitch pin hole to the nearest part of the step platform on # C31001 is 5-1/4 inches. So from the center of the pin hole out all the way to the end of the step would be 11-5/8 inches.

expert reply by: Michael H

0

click to enlarge

Answer 1

I have a solution for you.The main concern I would warn you about in this scenario is that if the weight that is either distributed on the ground or on the trailer exceeds 1500 pounds for even a brief instant, it could not just potentially damage…

view full answer...

Answer 2

I spoke with my contact at CURT and he stated that the Step, #C31001, is 6-3/8 inches front to back and 10-3/4 inches wide. I have made a picture showing these dimensions for you.

view full answer...

Answer 3

I spoke to my contact at Horizon Global. He said it is acceptable to mount the Bulldog Powered-Drive Kit #BD1824200100 to the slave jack itself. He also said that if you need to switch the motor wires to make it work correctly, that would be fine,…

view full answer...

Answer 4

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...

Answer 5

The etrailer Trailer Hitch Receiver #e72AR weighs in at around 25 lbs so it isn't overbearingly heavy, but I do recommend having an extra set of hands nearby to help hold it in place until you can get the hardware started on your 2024 Acura…

view full answer...

Answer 6

The 35lb weight calculation for the Swagman Patrol 2 Bike Rack #S64701 is based on the weight of the bike connected to the rack. So this will be the weight of the bike minus the front wheels. It is not going to work for your two 70lb E-bikes.…

view full answer...

Answer 7

Unfortunately the bumper step like the Bestop TrekStep #B75306 is not universal to fit both sides. There is not a passenger side option for your 2017 Ram 3500. For your passenger side step, you may be interested in the Wheel Mount Tire Step #HE4040…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

TorkLift Space Dock part #TLA7900 is intended for use on the Palomino Landing Pad bumper to allow installation of the TorkLift Lock and Load SideKick generator tray #TLA7901. The Black Rock Special Edition Space Dock was designed specifically for…

view full answer...

Answer 10

The Space Dock 2" Receiver Adapter for Torklift Palomino Landing Pad Bumper #TLA7900 is designed to be used with the Palomino Land Pad, so as long as you have this on your 2021 Palomino 2902 Camper then this'll work great. Also, this…

view full answer...

Answer 11

Draw-Tite front hitch #65067 and the USA-made Curt #C31083 are both confirmed fits for your 2018 Ford F-150 Lariat Super Crew HD FX4. Both hitches share the same weight ratings and bolt on to the same mounting points for a no-drill installation. I…

view full answer...

How Far Out is the Platform from Hitch Pin Hole on Curt Hitch Mount Step 31001

Product Page this Question was Asked From

Continue Researching