Recommended Brake Controller for 2010 Toyota Tundra Towing 7000 lb Travel Trailer

Question

Question:

Which brake controller would you recommend for a 2010 toyota tundra, pulling a travel trailer 7000 lbs.

asked by: winston l

0

Expert Reply:

Brake Controllers are not vehicle specific, so just about any controller would work for you. This being said, I would recommend you go with a proportional type brake controller. A proportional controller features an internal sensor that can determine how quickly and at what intensity the tow vehicle is braking. The controller will then send the appropriate amount of voltage to the trailer brakes so that the trailer and tow vehicle stop at the same rate. This makes for a safer stopping action, as well as causing less wear and tear on both braking systems.

Of the proportional controllers we offer, you cannot go wrong with the Tekonsha Prodigy P2, part # 90885. This controller is one of our best sellers and is very easy to install and operate. We also offer the Brake Controller wiring adapter, which will allow the controller to plug into the connector under the dash located by the emergency brake pedal.

The correct vehicle specific adapter for your 2010 Tundra is the # 3040-P.

If your Tundra is equipped with the 4-pole connector that controls lighting functions only, you will need the Brake Controller Installation Kit, part # ETBC7. The kit contains everything necessary for installing your controller, including the 7-way trailer connector.

expert reply by: Mike L

0

Answer 1

As long as you stay under the 10,300 pound mark you should be fine. Currently your trailer and gear estimate would weigh 9,100 pounds. Take a look at the rig when the trailer and truck are fully loaded as though you were ready to hit the road. If the…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

To install your Tekonsha Prodigy on your 2000 Toyota Tundra, you will need the Brake Controller Install Kit, part #ETBC7. The kit includes all necessary parts and hardware for installing a controller on your vehicle. We have some online resources you…

view full answer...

Answer 4

As far as function goes, the two controllers are actually pretty similar. The primary difference between the two is that the P3 uses what I would call a more user friendly display. Instead of an error code like what's displayed on the P2, the P3…

view full answer...

Answer 5

If your 2011 Tundra has the factory tow package, which includes the factory installed 7-way trailer connector on the rear bumper, it will be equipped with the tow package plug under the dash, as shown in the photo I've edited for you. Some models…

view full answer...

Answer 6

The brake controller I recommend for your 2013 Toyota Tundra is the Prodigy P3, part #90195. It's our top selling brake controller because of how easy it is to use and how reliable it is. Since you have a factory 4-way trailer connector on your…

view full answer...

Answer 7

Karrier and Loadstar are two different brand names used by Kenda. There's no difference in quality or function between the two brand names. For a ST175/80-13 Radial trailer tire in load range D, I'd recommend part #AM10210 if you're…

view full answer...

Answer 8

The size difference between the Kenda Karrier ST175/80R13 Radial Trailer Tire - Load Range D #AM10210 and a 185-80R13 tire is the diameter and the width. We don't have any radials in that size, so I'll compare to the similar Kenda Loadstar…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...