Parts Needed to Inflate Tires with Air Lift Load Controller Compressor for Air Helper Springs

Question

Question:

What additional accessories do I need to accomplish tire inflation with this system?

asked by: Steve B

0

Expert Reply:

The Air Lift Load Controller I Compressor System for Air Helper Springs, # AL25651, is meant to keep air springs inflated, it wouldn't be a good product for inflating tires. To inflate tires, you'd want a compressor that's specifically designed for that purpose, like the Bulldog # BDW41000.

expert reply by: Chris O

0

Answer 1

We do have the Air Lift Heavy Duty Compressor kit with the part #AL25651 that you are looking for.

view full answer...

Answer 2

It is possible to add an air tank to your #AL74000EZ. What you need is the AirLift #AL87DQ. This upgrade kit comes with an additional compressor, a 2 gallon tank, and all of the parts required to add the tank to your Air Lift WirelessAIR Compressor…

view full answer...

Answer 3

The Air Lift QuickShot Compressor System #AL25572 is a great choice for an onboard air compressor that will work with the Firestone Ride-Rite Red Label Extreme Duty Air Helper Springs #F2710 and will also allow you to fill tires. This will not be…

view full answer...

Answer 4

Hello Cory. I can definitely point you in the right direction, but there is not a B&W Companion option that will fit into a round gooseneck ball hole. As you said, the B&W Companion hitch is only compatible with the B&W Turnoverball…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

There's not many differences between the Air Lift WirelessONE item #AL25980EZ and item #AL25980. The main difference is that the item #AL25980EZ has a slightly higher CFM at 1.03 compared to 0.92 and it runs slightly more efficient at 9% over 15%…

view full answer...

Answer 7

The Air Lift WirelessONE Compressor System #AL25980EZ and Air Lift WirelessONE Compressor System #AL25980 are nearly identical with only some very minor differences in CFM and duty cycle ratings. The #AL25980EZ will also come with an easier mounting…

view full answer...

Answer 8

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 9

That's good you've identified the issue and I do agree it does sound like the module. However, we do not have replacement modules for Air Lift compressors. I recommend getting a part number off of your compressor and reaching out to Air Lift…

view full answer...

Answer 10

The option that will work for your 2017 Cherokee 29TE depends on your axle diameter. For 2-3/8 inch axles, you will want the Dexter Trailer Springs Over-Under Conversion Kit, #K71-384-00. If you have a 3-inch diameter axle, you will want the kit,…

view full answer...

Answer 11

You do not need to remove the bed of your truck to install the HappiJac part #LC182906-182971 that you referenced. I found a copy of the install instructions for this part number (see attached pictures) and there's no mention of the bed needing…

view full answer...

Answer 12

Yes, the Curt Trailer Hitch Receiver #C15809 will fit your 2003 Dodge Ram 3500. This receiver is capable of fitting with the factory receiver still installed or no factory receiver present, That is why it looks different from your factory receiver in…

view full answer...

Parts Needed to Inflate Tires with Air Lift Load Controller Compressor for Air Helper Springs

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching