Availability of a Top Cap for the Ultra-Fab Leveling Blocks

Question

Question:

Can you get top cap for them.

asked by: Jimmy

1

Helpful Expert Reply:

The Ultra-Fab leveling blocks # UF48-979051 are designed for leveling trailers and RV's and the reason they are quite rigid on top and extremely durable. I called our representative at Ultra-Fab and there isn't any type of top cap available. You can use an additional set to increase their height as needed since they are stackable.

expert reply by: Chris B

1

Answer 1

You're correct, you'd need to use trial and error. However, you could use a leveler like part #HM09615, which would eliminate a lot of guesswork and eyeballing.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

When it comes to choosing between the Blue Ox Patriot #BLU37TR and the Brake Buddy Select 3 #HM39524, these systems are extremely similar in their setup and functionality. Both of these systems provide proportional braking in a compact and easy to…

view full answer...

Answer 6

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

What you need is a light kit specifically for flat-towing. The Plug-N-Tow TM Vehicle Wiring Harness, #42615, would be if the Jeep were towing a trailer and not for activating its lights while it is being towed. There are a few options for lighting…

view full answer...

Answer 11

Great question! The Brake Buddy Classic 3 #HM39494 is a more basic system than the Brake Buddy Select 3 #HM39524 as the Classic just uses preset braking (which applies the brakes at a preset intensity when the inertia sensor detects deceleration)…

view full answer...

Answer 12

For your 2024 Hyunda Santa Cruz we have the Curt 7-way kit part #C68JR that is a confirmed fit. This installs by plugging into a factory wiring connector on your vehicle which means a really easy install that doesn't require any splicing.

view full answer...

Availability of a Top Cap for the Ultra-Fab Leveling Blocks

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching