Availability of Replacement Velcro Strips for a Tonneau Cover

Question

Question:

I am looking for new velcro to attach to my bed rails. It is glued. I have tried to do this myself with no luck. I need to know which product line I should buy from you, new velcro and glue needed to adhere it to bed rails. Thank you. I have a 2005 F-250 Ford short bed.

asked by: Richard S

0

Expert Reply:

Without knowing what brand tonneau cover you have on your 2005 Ford F-250 it is hard for me to say for sure what replacement hook and loop strips you would need. But if you have a Truxedo or an Access check out the links I attached to the right.

expert reply by: Jameson C

0

Answer 1

I pulled the Replacement Velcro Strip, part #A30474 from the warehouse and opened the package to see how it is attached. This is designed to replace the hook side of the velcro fastener on Tonneau covers. Per the instructions you would drill out the…

view full answer...

Answer 2

You can use the Replacement Truxedo Shur-Bond Velcro Brand Fastener for 8' Beds - 1" Width #TX1117877 which is the width you need and can be cut to length. It doesn't have the adhesive back but rather fits in the groove of the rail.

view full answer...

Answer 3

The only difference between the Access Replacement Velcro Strips #A30474 and #A60270 is that A30474 is 1-1/2 inches wide and A60270 is only 1 inch wide. They are both 17 feet long and come with the 4 screws to help keep them in place.

view full answer...

Answer 4

Yes, I confirmed with my contact at TruXedo that the Replacement TruXedo Shur-Bond Velcro Brand Fastener for 8' Beds #TX1117877 comes with 2 1-inch Velcro fasteners.

view full answer...

Answer 5

There is a tonneau cover that fits your 1998 Chevy C/K fleetside with a 6-1/2 foot bed that I recommend, from Access, and is the following part number: - Access TonnoSport Soft, Roll-Up Tonneau Cover #A22020129 I really like the TonnoSport #A22020129…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...