To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Quickly and easily install a 4-way trailer connector on your vehicle with this custom harness. T-connector plugs directly into existing wiring. Powered converter reduces strain on wiring system and is made using SMT to ensure superior performance.
Features:
Specs:
Installation
This custom-fit T-connector plugs into your vehicle's wiring harness, which is located behind the driver's-side and passenger's-side tail lights. You will have to remove the trunk floor coverings and rear scuff panel, and pull back on the trunk liner to access these connection points. Once you've plugged in the T-connector, run the hot lead up to your car battery. Connect the lead to the included fuse holder, and then connect the fuse holder to the positive terminal on your battery.
Once installation is complete, the 4-way connector will be stowed in an out-of-the-way location within your trunk.
It is recommended that you use a small amount of grease on all electrical connections - the plugs on your automobile and the 4-pole connector itself - to help prevent corrosion.
A tail light converter is built into this T-connector. This converter is a circuit-protected, battery-powered unit that bypasses the electrical routes that are used by a basic wiring harness. As a result, there is virtually no draw on your tail light circuits.
Because most trailers run on a two-wire system - wherein the brake and turn signals are carried on one wire - the separate brake and turn signals from your vehicle's three-wire system need to be combined so they are compatible with the wiring system of the trailer. This converter combines the brake and turn signal functions of your automobile so that they run on one wire to properly activate your trailer's tail lights. Note: This will not affect how the tail lights on your vehicle operate.
Curt builds each tail light converter using surface-mount technology (SMT). This method of construction involves soldering electronic components directly to the surface of a printed circuit board. SMT eliminates the need for leads, which are used in older through-hole technology. The result is a circuit board that is smaller yet provides more routing area and that offers superior performance, reliability and durability.
Circuit boards constructed using SMT have been shown to perform better under rough conditions with excessive vibration than those made using the through-hole method. And where would vibration be more likely to occur than in towing applications? Curt converters also produce less heat, leading to increased durability and longer life. In addition, lower levels of resistance ensure better performance, especially for parts that operate at higher frequencies.
Each Curt circuit board is made using high-quality components that are pieced together in the most technologically savvy fashion, leading to greater predictability and reliability in functioning.
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today we're going to take a look at the Curt T-Connector Vehicle Wiring Harness with the 4-way Flat Trailer Connector. This part is a custom fit part. It is designed to fit the Buick Verano vehicle starting in the year 2012. On any custom fit part what I always recommend is to go to our website, use our fit guide, put in your year and model vehicle and it'll show you if this will work for your application. This harness will provide this 4-way flat trailer connector at the back of your vehicle to power your trailer signal lights. It connects very quickly and easily. Basically just locate your connection points in the rear cargo area, plug in these T-connectors, one on each side, ground this white wire and then run this hot wire or power wire to the vehicle's battery to supply power to the converter.
You'll be all ready to go. This harness does include this tail light converter. This is to ensure that your vehicle's wiring will match that of your trailer. It is a powered module that's why you'd connect it to the battery and connecting it to the battery helps you avoid overloading your vehicle's electrical system. The converter itself is constructed using SMT Technology, which is surface mount technology. That technology gives you a consistent, reliable performance.
It'll maximize your trailer light yield and intensity while producing minimal heat. It'll also ensure superior operation in any rough road conditions. The other nice this is if you notice it comes with this dust cap for the 4-way. Basically what you can do with this is just attach it to the 4-way connector. You can leave it on there if you'd like, but when you're not plugged into your trailer you can just pop your dust cap over the terminals and it protects them from any damage or from the elements. A few specs on this, the maximum amperage for the stop and turn circuits are 3 amps per circuit.
On the tail light circuit it's 6 amps total. This part comes with everything show here. It even comes with a nice set of detailed instruction that describe how to install it and even gives you pictures of where your points are to connect it to. Simply when you go to install this what you would do is go to the rear of your vehicle, and again you locate your connection points which are in the rear cargo area. You'll find connectors that'll match these.
What you'll do is you want to start on the driver side and take the T-connector that has the yellow wire in it and pull apart your connectors and then plug this or T it into the wiring harness. Then again you'll have this white wire with the eyelet on it that you'll want to connect to a good clean ground. If you have one nearby you can do it. If you need to make one just drill a hole and use the grounding screw they include. Then you'll take the other T-connector that has this length of green wire, that's for the passenger side. Run this over to the passenger side. Again, unplug your connectors, plug this into that and then what you'll want to do is you have this black wire which is your power wire which you need to run to the front of the vehicle to connect to the battery. Before you do that what you want to do is on your converter, you don't this bouncing around, so they include this piece of double face tape that you can put on it and attach it, so it doesn't move around, to a nice flat surface. You'll take your black power wire here and they'll give you this extra length of wire. You'll take your included butt connector, put it on the power wire, connect it to one end of this length of wire. Then you'll run this length of wire all the way up to the front of your vehicle. Once you get to the front with this other end, you don't want to connect this directly to the battery, you want to run it through an inline fuse holder. They include this inline fuse holder, so again you'll take your connector, put it on one end, connect it to that power wire coming up front. On the other end you'll take the eyelet connector and install that. This is what you connect to the positive post of your battery. Once that's all connected just pop open your fuse holder, take your included 10 amp fuse, put it into the . there you go, push it in and then just put your cap over there and then your fuse is installed. Now your harness is all ready to plug in and supply lights back to your trailer. That should do it for the review on the Curt T-Connector Vehicle Wiring Harness with the 4-way Flat Trailer Connector.
Average Customer Rating: 5.0 out of 5 stars (4 Customer Reviews)
Quickly and easily install a 4-way trailer connector on your vehicle with this custom harness. T-connector plugs directly into existing wiring. Powered converter reduces strain on wiring system and is made using SMT to ensure superior performance.It worked out great. Instructions were easy.
Trailer Hitch/Electrical kit delivered the next day on a regular order shipment. Hitch installation took less than hour, Electrical took an hour for a 2015 Buick Verano. Saved over $150 from a dealer install.
Thanks.
I found product on website, which was easy to navigate. Ordered via toll free number. Customer service was very friendly. Product was shipped very fast. Product instructions were easy to follow. Hooked up and worked like advertised. Highly recommend this company and their products.
Everything fitted like expected and it works.
Do you have a question about this Custom Fit Vehicle Wiring?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.