Curt hitch step # C31001 is an excellent option. The step is made of steel butt it has an anti-skid surface on top for safety. I have linked a video review of this step for you. We also carry grip tape, # CAM25401, if you have any other surfaces that could use it! view full answer...
The Round Tube Stainless Steel Trailer Hitch Receiver Step with LED Lights for 2" Trailer Hitches # CR-600LED only has the Replacement LED Strip for Bully Round Tube Hitch Step # CR-600L-LED. The rubber end caps are not available as replacement parts, so you would need to replace the entire step. view full answer...
I checked with Reese and they do not offer any replacement parts for the Reese Towpower Tow & Go Hitch Step part # RP7060200 so if the plastic piece is broken you will have no other option but to replace the entire unit unfortunately. view full answer...
I went ahead and reached out to my contact at Pilot Automotive, and they unfortunately confirmed that the pad for the Bully Black Bull LED Hitch-Mounted Step for 1-1/4" and 2" Hitches # BBS-1104L is not sold individually. If you wish to get a new pad, the step must be replaced. view full answer...
To replace your wiring on your Bully hitch step # CR-600LED I recommend the Hopkins Wiring Harness with 4-Pole Flat Trailer Connector # HM38138 along with heat shrink connectors # DW05743-5. For added protection you can add a wire loom like # 7509-1 sold by the foot.
The wires of this harness have the following functions for you to match up to the wires in the step.
White: ground wire
Yellow: left turn/brake light
Green: right turn/brake light
Brown: tail lights view full answer...
According to my contact at Pilot/Bully their Round Tube Stainless Steel Trailer Hitch Receiver Step with LED Lights # CR-600LED does not have a replacement step pad available but we do offer the Replacement LED Strip # CR-600L-LED. view full answer...
You will need to wire the Hopkins 4-Way Flat Trailer Connector # HM48133 to the Replacement LED Strip # CR-600L-LED. There is not a harness with both connectors as neither end will fit through the small hole in the Round Tube Stainless Steel Trailer Hitch Receiver Step # CR-600LED.
I recommend using Deka Heat Shrink Butt Connectors # DW05743-5 to seal the connector inside the step since water can get inside the step. view full answer...
I have a couple universal options as I have no way to verify what parts were installed on your 2002 BandS Sportsman boat trailer. If none of these options listed below are what you are looking for please send me some images and measurements for your step and I can see what alternatives you have.
HitchMate Boat Trailer Step # HE4036
CE Smith Galvanized Steel Step for 2" Trailer Frame # CE26212G-15284GA
CE Smith Steel Step for Trailer Fender # CE19012, # CE19011 view full answer...
For replacement gear box linkage for the existing Kwikee steps on your motorhome, I recommend the Lippert Kwikee Step Gear/Linkage # LC379160. This is specifically designed for certain electric steps in the Kwikee series including your Series # 32 model.
The cost will be listed on the product page. view full answer...
For a replacement LED light for the Bully Round Tube Stainless Steel Trailer Hitch Receiver Step, # CR-600LED, you will want the Replacement LED Light, # CR-600L-LED. view full answer...
The boards/steps that are mentioned in the fitguide for the Torklift camper tie downs refers to the steps you sometimes see under truck cabs to make getting in and out of the truck a bit easier. Some call them nerf bars, side steps, tube steps etc.
Let's say you got an 8 foot bed 2021 Chevy Silverado 3500 with side steps, and a factory hitch. You'd want the part # TL44FR and # TL84FR.
If you had a different configuration let me know or follow the link I attached on this page where you... view full answer...
It sounds like you might have the Round Tube Stainless Steel Trailer Hitch Receiver Step with LED Lights for 2" Trailer Hitches # CR-600LED and to replace the 4 way connector on that you can use the 4-Way Flat Trailer Connector - Trailer End # 18004. The 4-way connector on the Pilot Round Tube step you've got is just a standard trailer 4 way connector, as there are not special connectors for LED lights, so this will work well for you.
You'll want to cut off the destroyed end and just... view full answer...
Yes, the Pilot Replacement LED Strip # CR-600L-LED is the correct item to replace the LED lights on your Bully Black Bull LED Round Tube Hitch-Mounted Step # BBS-1104L. The kit includes the LEDs, wiring and adhesive strip. view full answer...
For replacement hardware to re-install the Draw-Tite Class V hitch # 41944 which fits various GMC and Chevy trucks you will use kit # RHK. Just enter that item into our search field and click GO. Then on that RHK page just enter the brand Draw-Tite and the part number # 41944 in the appropriate fields. We will put together a complete kit for you.
You can also refer to the linked instructions for this hitch which will tell you all of the tools needed as well as give you complete step by... view full answer...
We offer replacement hardware kits for all hitches we sell. The item number for the hardware kit is # RHK.
The 2-inch Curt Class III hitch made for the 2009 Ford Flex with single exhaust is part # 13551. This is a custom-fit hitch made specifically for the 2009 - 2018 Ford Flex without dual exhaust. You will need to verify your hitch part number before ordering hardware.
For new hardware for this hitch simply enter the hitch part number in the appropriate field on the page for kit # RHK... view full answer...
If you move up to the 1,200LB Equal-i-zer Hitch Head # EQ90-02-1200 you will need to use the larger 1,200lb weight distribution Spring Bars # EQ90-01-1299 with the hitch as they use larger spring bars.
To use your current spring bars you will need the 1,000LB Equal-i-zer Hitch Head # EQ90-02-1000. view full answer...
You sure can get it here at etrailer.com!
The replacement hardware for the TorkLift SuperHitch Magnum Trailer Hitch Receiver # TLF1002-30 that you referenced is found as part # TLM8003-F1002-30 on our site. The installation instructions have been linked for you to reference as well in case those were in the box.
Please note that this trailer hitch fits Ford F-350 models from 1999 - 2016 (1999 - 2004 fits a Standard or Step Bumper). view full answer...
The Draw-Tite Class III hitch you'd looked at, part # 75676 uses 6 M12 x 1.25 x 40mm (12 mm diameter with a 1.25 thread pitch x 40 mm long) class 10.9 bolts to secure the hitch to the nuts that are welded into the frame of your Lexus RX350.
We offer a replacement hardware kit as part # RHK. On the product page, you'd input '75676' as the hitch item number and choose 'Draw-Tite' from the drop down menu. This will provide all the hardware that originally came with the hitch.
I've linked... view full answer...
For the B&W Turnoverball Underbed Gooseneck Hitch that is already installed on your 2011 Dodge Ram 2500, you will want the B&W Replacement Hitch Ball for B&W Turnoverball Hitches # BWGNXA2000. This is B&W's standard replacement gooseneck ball for their Turnoverball hitch.
I spoke with my contact at B&W and she confirmed that this is the correct replacement gooseneck ball for your 2011 Ram 2500.
The price of the replacement ball is listed on the product page as well as in the product... view full answer...
The Curt Class III hitch you referenced, part # 13591 will fit your 2015 Equinox.
However, please realize that the installation hardware you originally used is designed for a one-time use only. You can certainly reuse the hitch, but I'd strongly suggest you obtain replacement hardware before doing so.
We sell replacement installation hardware as part # RHK. On the product page, type in # 13591 as the part number choose Curt from the drop down menu.
I've linked you to the installation... view full answer...