Expert Answers about Toyota Highlander
- Replacement Hardware for Thule Mountaineer Cargo Box
- For replacement hardware for your Thule Mountaineer you can use the # 1032802. The plates look a little different but they have the same bolt hole spacing. If you want the quick on/off brackets you will also need 4 of the # TH04973. The protector pads # TH05001 are also available separately.
view full answer... - Replacement Strap With Button For Curt Echo Brake Controller
- The button you're referring to is for sure replaceable, as it's just a part of the strap for the Curt Echo Wireless Trailer Brake Controller # C51180. So all you need to do is replace the strap and you're set! The correct part number for the strap is the following:
- Replacement Strap for Curt Echo Wireless Trailer Brake Controller # C28HR
view full answer... - Replacement Hardware for Trailer Hitch on 2007 Toyota Highlander
- You'll need (6) M10 - 1.25 x 30 Class 10.9 hex bolts and (6) 3/8 inch conical toothed washers.
We offer them in the # RHK kit you'd looked at, On the product page, you'll input the hitch part number and choose the hitch manufacturer from the provided drop-down menu.
If you wish, you should be able to find the bolts locally, but the conical tooth washers are a specialty item that you'll probably not find at your local home center. We offer them as part # 01292006-020-01.
view full answer... - Replacement Dexter Hub Drums and Brake Assemblies for Drums With 8-247 Casting Number
- You have a typical 3500 lb brake hub/drum. The correct replacement drum would be # 84546UC3 for standard spindles or # 84546UC3-EZ for an E-Z Lube spindle. The hubs include the inner and outer wheel bearing, inner and outer races, the grease seal, dust cap and lug nuts. The hub/drums are sold individually. As you can see in the photo, this hub has the same casting number as yours, so it is a proper replacement.
The Dexter 023-469 is a self adjusting 10 inch brake assembly. To replace it,...
view full answer... - Replacement Key for a Sears Sport SV-20 Cargo Box
- To find a replacement key, you'll be looking at Thule's keys, as SportRack is equipped with their locks.
To find your key, search for "THKEYNXXXX" where XXXX is replaced by the number printed on the front or side of your lock. For instance, if your lock is number 2862, you'll search for part # THKEYN2862.
If you cannot find your key number, let us know and we'll be happy to help you find the right replacement parts.
view full answer... - Idler Hub With 4 Lug Bolt Pattern For a Harbor Freight Trailer With 25mm Spindle Shaft
- We have the Easy Grease Trailer Idler Hub Assembly # AKIHUB-440-2-EZ-1K which should fit your Harbor Freight trailer. This idler hub includes bearings for a 1" spindle which is 25.4mm. It has a 4 on 4" bolt pattern. You can verify this is the correct dimensions for your trailer to verify it is the correct hub. This hub does also include a grease seal with 1.249" inside diameter grease seal. If you have a different size grease seal please let me know and I can determine if there is a different...
view full answer... - Replacement Round End Cap for a Thule Parkway Bike Carrier
- We have replacement round end cap # 853-2181 for Thule bike racks that have round tube arms. It fits 1-inch diameter arms. It has the hole at the bottom for the screw to hold it to the end of the rack arm.
view full answer... - Replacement Wrench for a Thule 91725U Snowsport Ski and Snowboard Carrier
- We have what you are looking for here!
The Thule 91725U Snowsport Ski and Snowboard Carrier has a replacement wrench available. It's the Replacement Tamperproof Wrench for Thule Ride-On Adapter, Bed-Rider, Flat Top, or Snowboard Carrier, part # 853-5270-02.
view full answer... - Replacement Wheel Strap For Swagman Current Bike Rack
- Even though the Replacement Wheel Strap for Swagman Bike Racks # S95YR does not list the Swagman Current # S64678 as a one of the models for a replacement, Swagman does list # S95YR as the correct replacement for your Swagman Current # S64678 bike rack.
view full answer... - Replacement Trim Rail Options For An Enclosed Trailer
- We carry quite a few different types/styles of trim so I've attached a link to our selection below so you can take a look. If you still want to send those pictures I can take a look myself and try to find the correct match. When you replace the trim I recommend using some butyl tape # AL28FJ on the back to help seal up the threads of the screws and some non-sag sealant # 344270341437-1 on the edges to prevent any water from getting behind the trim and rotting the walls of your trailer.
view full answer... - Solution for Needing Tekonsha Trailer Taillight Harness for 2021Toyota Highlander w Converter Box
- I wish that was available by itself but the only way to get the harness of the # TK99FR that has the taillight converter is to order the entire kit.
view full answer... - Replacement Rubber Straps For The Rhode Gear 4 Bike Hitch Shuttle Bike Rack
- I called my contact at Yakima and they informed me that they currently do not make nor stock replacement parts for the Rhode Gear 4 Bike Hitch Shuttle anymore. However, I suggest trying the Replacement Rubber Straps for Yakima BedRoc and Older Big Horn Models part # Y8820103 as these are very similar to your current support straps and according to the Yakima representative, should work for you. I would also agree with this statement as they do look very similar though, but since they have...
view full answer... - Trailer Hitch, Wiring and Weight Distribution System Recommendation for a 2004 Toyota Highlander
- First let's start with a trailer hitch for your 2004 Toyota Highlander. The Draw Tite part # 75153 that you referenced would be an excellent choice confirmed to fit.
You will need trailer wiring too. For that the part # 118413 has been confirmed as a fit. I attached install videos for both of these products.
The best way to pick out a weight distribution system is to base it off of the loaded tongue weight of the setup when it is loaded and ready to tow. This figure also includes the...
view full answer... - Replacement Hardware Kit for Re-installing Trailer Hitch on 2005 Toyota Highlander
- Don't worry about not having the old mounting hardware for your hitch; you cannot re-use it anyway since hitch mounting hardware can be torqued to spec only one time. After that it must be replaced with new hardware.
We offer kit # RHK, which is a replacement hardware kit for every hitch we sell.
Both aftermarket hitches made for your 2005 Toyota Highlander, Curt # 13530 and Draw-Tite # 75153 are shown on the linked page. Take a look at your hitch's safety sticker to find its part number...
view full answer... - Replacement Hardware for Draw-Tite Class III Trailer Hitch on a 2008 Toyota Highlander
- There are 2 possible Draw-Tite Class III trailer hitches for the 2008 Toyota Highlander.
Hitch # 75726 comes with 9 of Hex Bolt – M10 x 1.25 x 30mm CL10.9 and 9 of Conical Toothed Washer – 3/8”.
Hitch # 75586 only uses 6 of each of the components above.
The replacement hardware kit is # RHK and you would enter the hitch number and manufacturer of the hitch on that page to get the proper hardware.
view full answer... - Have The Nylon Hitch Locks Been Replaced On The Rocky Mount Monorail
- The RockyMounts MonoRail Solo Bike Rack for 1 Bike - 1-1/4" and 2" Hitches - Wheel Mount, part # RKY10007, will come with the nylon lock. The premium lock only comes on the RockyMounts SplitRail and the RockyMounts BackStage. You can get the Replacement Hitch Lock Pod for RockyMounts Bike Rack, part # RKY12006, and replace the nylon lock with a premium metal lock.
I have included a product description link, a video review of the Rocky Mounts MonoRail, and a demo video of the Lock Pod below.
view full answer... - Replacement Suction Cup Mounting Bracket for Voyager Observation System # WVOS713
- The correct replacement suction cup mounting bracket for your Voyager WVOS713 monitor is the part # PVOS7SCM. The bracket on this unit is designed specifically for the larger 7" monitor on your system.
The Replacement Mount # PVOS5SCM that you referenced is for the smaller 5" monitors so it won't work well to secure the larger size.
view full answer... - What Bolt Size is Used to Install Curt Trailer hitch 13200 on a 2014 Toyota highlander
- Curt trailer hitch # C13200 uses six M12-1.25 x 35mm grade 5 hex bolts and six 1/2 inch conical tooth washers. If you bought the hitch from us then the hardware should have been taped up around the receiver or stuffed inside the receiver. If it was missing then give us a call!
Otherwise we can get you the proper hardware if you order # RHK. Put in the hitch number and choose Curt as the manufacturer to get the right kit.
view full answer... - Parts Needed to Install Brake Controller 2018 Toyota Highlander with Aftermarket 7-Way
- A 2018 Toyota Highlander would not have come with a factory brake controller as that is not a factory option. Even more so if the vehicle only had a 4-way installed from the factory. That said we can help you wire a brake controller to your current aftermarket 7-way.
For a wiring kit to install the brake controller to the 7-way you would want the Wiring Kit for 2 and 4 Brake Electric Brake Controllers # 5506. This will provide the power source and ground for the wiring for the brake controller....
view full answer... - Replacement Jack for 1997 Starcraft Meteor 814 Classic
- We don't offer a replacement jack that would be compatible with the bracketry you show in your photo, but we do offer an option that would work for you.
Folks use side-mount jacks on A-frame trailers all the time, but as you found they're not very stable because of the tilting force placed on them because the load is off-center. I'd recommend replacing your existing coupler with part # CA-5100-Z which would provide a strong and secure mounting location for the jack. The coupler is a weld-on...
view full answer...
Go To Results