The best weight distribution system without chains (some argue even with chains) is for sure the Equal-i-zer weight distribution system part # EQ37061ET. This is essentially the system that all other WD companies measure themselves against as it's long been considered to be the best and original WD system. It has a really effective sway control and is extremely high quality so it will perform great and lost a very long time. view full answer...
For cushioned equalizers you'd want to measure the distance between the left and right bolt holes and we can pick out what you'd need from there. For example if the distance is between 7-1/4 inches and 8-1/4 inches the EZ Flex part # K71-653-00 would work great but if you have something else let me know. This kit comes with wet bolts and brass bushings too so that would be covered as well.
Then for a lift kit the Lippert kit part # RR23QX would give you a lift of 2 inches. view full answer...
The only lift kit we offer for this application is the Correct Track Trailer Alignment and Lift Kit part # RR23QX which is basically a leaf spring hanger extension that will provide a lift of 1-1/4" or 2-1/4". It can be used with both underslung and overslung axles. It features a simple bolt-on install. view full answer...
Since you have a Lippert 1621 pin box on your 2018 Durango Gold 380FLF the correct Sidewinder is the part # RP61422 that you mentioned.
So you'd want to use a fixed hitch with the Sidewinder and since you want a lower height one the Reese part # RP30047 would be a great option as it's height range is 13-1/2 inch to 17 inch. view full answer...
The Lippert Scissor Stabilizer Jacks # LC285326 are only stabilizer jacks that should not be used to try and lift or lower your 2014 K-Z Durango 336RE.
For lifting the front for connecting and disconnecting the camper there are a couple options to help you with that. The jacks will have a manual override on the top of the jack. You will remove the access cap and use a ratchet to move the jacks. You can also disconnect the wiring on the jack and operate it remotely by powering the jack... view full answer...
In regards to a trailer wheel and tire assembly, the psi rating comes from the trailer tire and valve stem. Therefore, if the psi rating of the valve stem exceeds that of the trailer tire you will not have any issues. The trailer wheel itself does not have any sort of psi rating. The highest rated valve stem we offer is the Americana Metal, Bolt-In Valve Stem part # AM20906 which is rated for over 100 psi. view full answer...
The Aluminum Bobcat Trailer Wheel part # LHSO513B for wheels with a 8 on 6-1/2" bolt pattern or the Aluminum Jaguar Wheel part # 274-000011 for wheels with a 6 on 5-1/2" bolt pattern is what I recommend for a 2019 K-Z Sportsmen Fifth Wheel. In regards to psi, this will come from the valve stem so as long as you use the Americana Metal, Bolt-In Valve Stem part # AM20906 you will be covered over 110 psi.
If you don't already have a trailer tire picked out, the Taskmaster Premium Trailer... view full answer...
The bearings your Lippert 5,200 lb axle has are part # LM67048 and # 25580 and the grease seal is # RG06-070. For a cotter pin you'd need just the # 165649. view full answer...
Since you measured the drums and found they are 10 inch that is your best indication what you need as replacement assemblies. For that the best solution is the self adjusting assemblies part # AKEBRK-35-SA which will fit and work great. The numbers you listed don't match anything I was able to find though. view full answer...
My research indicates that the 2015 K-Z Spree Connect is about 28 feet including the A-frame/coupler, while the body of the trailer is about 25 feet long. If that's the case, I'd recommend the Adco # 290-52243 which will fit travel trailers up to 26 feet long. The cover provides good protection against UV radiation, rain, wind and dust. The cover is breathable to prevent the formation of mold and mildew which is important in your humid climate. The cover also offers zippered openings on... view full answer...
Yes, the Ultra-Fab 5th Wheel King Pin Tripod Stabilizer - Steel - 37" to 50" - 5,000 lbs # UF19-950001 will work as long as your pin box height is within 37 to 50 inches and the pin weight is less than 5000 pounds. view full answer...
Flipping your axles does not require a lot of parts and isn't too complicated. What you need is the Dexter Trailer Springs Over-Under Conversion Kit. You will need to find your axle diameter to choose the correct kit. For a 2-3/8" axle you need the # K71-384-00 and for a 3" axle the # K71-385-00.
This will raise your K-Z Sportsmen Sportster the diameter of your axle plus the height of the leaf spring stack. There are no additional blocks you can add, but you could add taller hangers to... view full answer...
We can start with the over-under conversion kit since that is pretty simple. Since you have a 2-3/8" axle you will need the Dexter # K71-384-00. This will allow you to mount the leaf springs on top of the axle on your 2012 K-Z Spree.
Moving on to the brakes, I'm assuming with your 2-3/8" axle that you have 3,500 lb axles. Make sure to verify this information. Assuming that is the case, you will need the following:
-Electric Trailer Brake Kit - Self-Adjusting - 10" - Left and Right Hand... view full answer...
For a bright white RV awning LED light strip we have the part # LC674282 which is 15 feet long but can be trimmed down to 13 feet like you need. view full answer...
The EC error code mean that the Fogatti Tankless Water Heater # LSB64FR tried to start the pilot light and was unable to due to low gas pressure. You'll want to have a licensed technician check to ensure you are actually getting 11"WC. It very well could be issues with the regulator and a new one would fix the problem like with the part # CAM59005. view full answer...
The best full suspension replacement option we have for trailers is the Roadmaster Comfort Ride Leaf Spring Suspension Kit part # RM-2460-2570. This is a complete kit which comes with new leaf springs, shock absorbers, and everything else needed for installation. The springs/shocks work great to improve traction and provide a smoother, quieter, and more controlled ride. The independent axle operation also increases traction by as much as 70 percent during braking view full answer...
From our research on your 2011 kz Coyote Lite CL164 your trailer actually has 3,000 lb axles so for a set of brake assemblies you'd want the part # K23-472-473-00.
Or if you are sure you have 3,500 lb axles the brake assemblies you'd want is the kit part # AKEBRK-35-SA and the hub/drum # AKHD-545-35-EZ-K. view full answer...
In order to choose the correct ball mount you need to measure the distance from the ground to the top inside edge of the trailer hitch and then subtract the distance from the ground to the bottom of the trailer coupler while the trailer is level. If the vehicle is higher than the trailer you need a drop but if it's lower you'll need a rise.
I have attached a full list of ball mount options below for a 1-1/4" trailer hitch. view full answer...
The weight distribution system I recommend for a K-Z Sportsmen Classic 160QB is the Equal-i-zer Weight Distribution System part # EQ37060ET. This is a complete setup ready to go. It's regarded as one of the best options on the market. It has integrated sway control, an included hitch ball, is made in the USA, and has a lifetime warranty.
The Equal-i-zer uses trunnion spring bars which provide the best ground clearance. Furthermore, the shank can be flipped and used in the rise position... view full answer...
Go To Results