Easiest solution would be to use the Reese rail kit adapter part # RP30156 which fits the rail kit of your 2018 Ford F-350 and provides a set of industry standard rails that your Curt hitch would fit directly.
Or for a hitch to fit the rail kit of your truck directly the B and W Companion part # BWRVK3300 is basically the best option around. It fits the pucks directly and will give you what most in the RV world consider the best fifth wheel hitch you can get. This is a fixed hitch so... view full answer...
The Brophy Bumper Spare Carrier part # BR56VR is approved for use at the rear of a motorhome like you have and as long as the wheel is less than 17-1/2 inches in diameter it would work well in that regard as well. view full answer...
34 inch wide trailer frame indicates you have a cab and chassis F-350, which we do have solutions for that. But if you have an RV built on a F-350 frame then we don't have a fit that I can guarantee will fit since the rears of those are quite a bit different in dimensions than most vehicles and vary from motorhome to motorhome.
The # 41947 will fit a 2017 F-350 Cab and Chassis and it is a Class IV hitch though. If your Ford isn't a motorhome this would be a great option.
The other option... view full answer...
Its not in our fitguide but the correct brake controller adapter to use a Tekonsha brake controller in a Ford F-53 chassis is the part # 3034-P.
For a brake controller I would recommend the Prodigy P2 Brake Controller part # 90885. This is our best selling brake controller because of how well it works and how easy it is to setup. This is a proportional brake controller that senses the amount of braking the tow vehicle is applying and applies a proportionate amount to the trailer brakes. view full answer...
For your 2017 Ford Class-C E-350 Dually + V10 engine we recommend the following.
Roadmaster # RM-1139-176 Front Anti-Sway Bar Kit
Roadmaster # RM-1139-117 Rear Anti-Sway Bar Kit
Roadmaster # RM-RBK24-RSSC Steering Stabilizer Kit
Many customers who have installed the anti-sway equipment have also used the SumoSprings helper springs to further stiffen the ride and decrease roll.
SuperSprings SumoSprings # SSF-106-47 Front helpers
SuperSprings Sumo Springs # SSR-130-54 Rear helpers
The... view full answer...
Yes, the Redarc Smart Start Battery Isolator # 331-SBI212D will allow you to have both batteries charging when connected to shore power. You'd need to put this inline with the charge that is currently going to the one battery so that you can run a charge wire to both batteries from it. view full answer...
We have the Curt hitch extender that fits 2-1/2 inch hitches part # C45048 and can be trimmed down from 34 inches to 24 inches.
At 34 inches it has a capacity of 6,000 lb trailer weight and at 24 inches 8,000 lbs trailer weight. view full answer...
If your 2017 Ford F-350 cab and chassis has all of the 7-way wires ran to the rear of the vehicle but no actual connector what you would need is the part # HM40975-11998. This is a 7 and 4-way that can be wired easily to the wires you have.
I attached an install video for you to check out as well. view full answer...
For a 5th wheel hitch that is a confirmed fit for the factory puck system in your 2018 Ford F-350 Dually, I have two options for you which will be dependant on bed length.
If you have the 6-3/4' bed then I recommend using the Demco Hijacker Autoslide 5th Wheel Hitch part # DM8550024. The best feature about the Autoslide is just that, it will automatically slide back away from the cab while making a sharp turn. This is going to ensure that you do not have contact between the cab of the... view full answer...
The best sewer hose system to store inside a rear bumper is the RhinoEXTREME RV Sewer Hoses w Swivel Fittings part # CAM39867. This system comes with caps to keep the odor contained so when you are done you can compress the hose, cap it off, and slide it into the bumper. That said, you need to store the adapter fittings separately as they won't fit inside the bumper but that is going to be the case for all of these 90 adapters. view full answer...
Since you are going to be using this on a boat trailer, I definitely recommend HydraStar. Their actuators are built of extruded anodized aluminum for corrosion resistance, have weathertight seals protect internal components, and include marine-grade gaskets and stainless steel hardware, so they are designed for use with boat trailers.
With that being said, we do not have a plug and play kit available for drum brakes at the moment, but we do have a kit that includes everything you need.... view full answer...
The Tekonsha Prodigy P3 Brake Controller, # 90195 and # 3034-P, will be all that you need to bypass you factory controller. This brake controller will hook up to your 2016 Ford F350 CC and bypass the factory controller.
The Ford factory brake controller that is in the dash does not have to be removed. You will need to unplug the connector under the dash and plug in the # 3034-P adapter for the Prodigy P3 brake controller to the factory brake controller plug behind the dash.
The vehicle... view full answer...
You can't go wrong with the Equal-i-zer Weight Distribution System w/ 4-Point Sway Control - 16,000 lbs GTW, 1,600 lbs TW part # EQ64FR It offers the best user experience and is among the best at eliminating sway as you head down the road.
You will need the 2-5/16" Hitch Ball part # C40008 and the Thin Walled Socket for Equal-i-zer Hitches part # EQ70-00-4800 to install the ball.
These three components are all you need to get the set up installed view full answer...
There isn't an install/rail kit for the B and W Turnoverball hitches that fits your 2023 Ford F-350 so there wouldn't be a way that we can recommend you install the B and W Hitch Center Section part # BWGNRC920 that you mentioned. The only way you could use this would be if you would be willing to fabricate a rail kit of some kind. Which if you were open to that the better option would be the part # BWGNRK1500 which was designed for this type of install. view full answer...
The Reese powered landing gear set part # RP500708 will work great for you. It's a dual motor landing gear setup that uses the same mounting bracket dimensions as the Stromberg setup you have now. view full answer...
The Lippert frame does not necessarily indicate you have Lippert axles, but since you have the capacity and other measurements it isn't a concern. The manufacturer information for your axles would be found on your axle tag. With 2-1/4" shackles you need the MORryde Suspension Upgrade Kit # MR46ZR.
For a MORryde upgraded equalizer you need the MORryde Rubber Equalizers # MR87ZR. These are designed to work with trailers that have a 33" wheelbase which matches your measurement. They also... view full answer...
For your 2023 Ford Edge Titanium I recommend the Curt Trailer Hitch Receiver # C13234. This Class III hitch with a 2" receiver. It has a max gross trailer weight of 4,000 lbs and tongue weight of 600 lbs. It features a bolt-on installation and comes with a lifetime warranty.
For wiring, the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # C73FR is confirmed to fit your Titanium. The T-connector plugs into existing wiring so no cutting or splicing is required.... view full answer...
The Draw-Tite # 65053 is a fit for the 2016 E450. I've confirmed this with Draw-Tite.
I attached an install picture of this hitch installed on a similar E-450 as yours for you to check out as well. view full answer...
Check out the attached link for the instructions with operating instructions for your Demco Hydraulic Brake Actuator part # DM8758521. view full answer...