The only option we have for trailer wiring for your 2004 Ford Crown Victoria is a hardwire option like part # 46255.
Or if you didn't want to splice any wires into your vehicle taillights you could use the zero contact kit part # 119250KIT that uses sensors to detect the vehicle taillight wiring instead of having to splice into them. You will still need to run a power wire up to the vehicle battery though. view full answer...
You would need to convert the 4-way to a 7-way so that you can install the brake controller. For that you will want the Brake Controller Install Kit and 7-Way Adapter part # ETBC7. I attached installation instructions and an install video for this product as well.
For a brake controller I would recommend the part # TK63VR. This is one our best selling brake controller because of how well it works and how easy it is to setup. It's also priced great too. view full answer...
I have another option for you, but the Curt Multi-Fit Trailer Hitch Receiver # C13900 you were looking at is not confirmed to fit your 2007 Ford Crown Victoria Police Interceptor.
Instead I recommend the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" # 13707 which is confirmed to fit your vehicle, and is a great option for carrying a bike rack like the Thule Hitching Post Pro # TH934XTR, a cargo carrier, or even light duty towing. You will need to drill a few holes in the vehicle... view full answer...
I did not know that having a sagging back end was cause to be pulled over. I know that some areas do have restrictions on how far off the pavement a vehicle can be. So first lets look at why the vehicle is sagging. If there is nothing in the trunk or back of the vehicle to weigh it down, and you have not modified it (like cutting the springs or used a lowering kit) then there is probably a problem with the suspension.
If your 2000 Ford Crown Victoria uses rear air shocks, that could be... view full answer...
The Draw-Tite Max-E-Loader Trailer Hitch Receiver part # 41116 is a great option for a 2009 Ford Crown Victoria and what I recommend using. It will fit models with dual exhaust. There are extra steps in the instructions for for fitment on these models. view full answer...
The only solution we have for you that would give you additional power and a more aggressive exhaust tone is going to be the MagnaFlow Cat-Back system part # MF16788 which is confirmed as a fit for your 2008 Ford Crown Victoria with a 4.7 liter V8.
Adding the part # MF35212 to your current setup will lengthen the exhaust but it would not make it any louder. view full answer...
For your 1998 Ford Crown Victoria we have the Hopkins trailer wiring harness part # 46255 as a confirmed fit that is designed to work with the taillight circuitry that your vehicle has. view full answer...
For your 2003 Ford Crown Victoria I recommend the Curt hitch # 13707. This is a Class III hitch with a 2 inch receiver rated for 400 pounds tongue weight and 4,000 pounds gross trailer weight so it covers the capacity of the vehicle.
Because your Crown Vic has dual exhaust there is some slight modification to the exhaust that will be needed to install this or any hitch for the vehicle. Its actually not all that difficult and I have included a link to a video showing an example installation... view full answer...
First you will need to verify the towing capacities of the 2009 Ford Crown Vic by checking the owners manual. If you already have a trailer hitch then make sure it is rated for use with weight distribution. There should be a sticker on the hitch that lists the capacities using weight distribution if the hitch is compatible. If it is not then you would want to add a different hitch such as # 13707.
This hitch is rated for 400 pounds tongue weight and 4,000 pounds gross trailer weight or... view full answer...
From my research your 2005 Fleetwood Colonial Pop Up uses 13 inch wheels with a 5 on 4-1/2 inch bolt pattern with ST185/80D13 tires. The Karrier ST175/80R13 Radial Trailer Tire with 13" Aluminum Wheel - 5 on 4-1/2 - Load Range D -Black # AM32001HWTB will work just fine with your trailer.
The 175/80R13 tires are radials for better traction and less heat buildup on the road. They will be 24.1 inches diameter with a section width of 7 inches. The factory wheel size is 24.7 inches diameter... view full answer...
We have a trailer wiring kit that was confirmed as a fit for your 2007 Ford Crown Victoria with the part # C59236 and allows you to run a wire to the battery and is confirmed to fit with your 2-wire setup. view full answer...
For a hitch for your 1993 Ford Crown Victoria Police Interceptor the etrailer hitch part # e66AR would be a great option. Then for trailer wiring the Curt kit part # C55326 is a fit and would install easily. view full answer...
I wish we had specific info on how to wire the part # C59236 to your 2002 Ford Crown Victoria but all we can recommend is to test the wiring like what you see in the install video I attached to identify the wiring functions of the taillight harness so that you can wire up the harness properly. view full answer...
First, you are going to want to make sure that the hitch is rated for use with weight distribution. Not all hitches are. There should be a sticker on the hitch that will indicate its capacity when using weight distribution. You have to do the same for the vehicle by consulting the owners manual.
If you need a hitch that is rated for weight distribution you can use # 13707. I have included a link to a video showing a typical installation and a link to the instructions.
For weight distribution... view full answer...
For your 2003 Ford Crown Victoria you can use Hopkins trailer wiring harness # 46255. There isn't a T-connector that just plugs into the taillight wiring available for your vehicle so you will need to use this hardwire harness.
You will also need a circuit tester such as # PTW2993 to test the vehicle tail light wiring. On the harness yellow is left turn signal, green is right turn signal, red is brake lights, brown is running lights, and white is ground.
The other red wire with the butt... view full answer...
I wish I could tell you which specific wire color you'd need to find on your 2011 Ford Crown Victoria but we haven't had the chance to install a brake controller on it so what you'll need to do is use a circuit tester like part # PTW2993 to test all of the wires that lead to the brake switch till you find the circuit that only has voltage when the brakes are applied. That's what you'll use to connect to the red wire of your brake controller.
I attached a help article on installing brake... view full answer...
The trailer hitch that fits your 2011 Ford Crown Victoria that has the highest towing capacities and would work great for towing your Integra would be the Curt hitch part # 13707. This can tow up to 4,000 lbs which would easily be enough for a lightweight Acura Integra. I attached an install video for this for you to check out as well.
For trailer wiring you'd also want the # C59236. view full answer...
For trailer wiring for your 1993 Ford Crown Victoria the part # C55326 is a confirmed fit. For your 1999 Mercury Grand Marquis you would need the part # C59236 instead.
I attached an install video that shows the harness being installed. view full answer...
I am not entirely sure I understand what you are asking but the catalytic converters are the same for both the base and police interceptor models of a 2001 Ford Crown Victoria. If you need to replace these then you will need two MagnaFlow Stainless Steel Catalytic Converter part # MF23328. This converter is a direct bolt-on fit for both the base and police interceptor models. view full answer...
The Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" # 13707 for your 2001 Ford Crown Victoria will not have the capacity you are seeking. It is only rated for 400 lbs tongue weight for this type of application so your bike and the carrier will far surpass its capacity. I recommend using a trailer along with this hitch to protect your bike as a carrier will not work with your vehicle.
For your wiring, I recommend the Hopkins Plug-In Simple Vehicle Wiring Harness with 4-Pole... view full answer...
Go To Results