Your 1997 Fleetwood Bounder motorhome is built on a Ford F-53 chassis so the correct steering stabilizer would be the part # RM-RBK4-RSSA. view full answer...
Basically you want to determine the size of the stereo you'll need first and then go with the stereo that fits that size that has the features you are in need of. For example, the Jensen RV Stereo part # JWM45 that you referenced fits the standard double din size found on most RVs and has 2 zones, Bluetooth, can play CDs, DVDs, HDMI, USB etc.
Since this is 2 zone this would be a great option if you have a set of indoor and outdoor speakers you wanted to be able to control as well. view full answer...
The Replacement PowerGear RV Above Floor Slide-Out Motor part # LC368417 is the correct replacement for a Power Gear 523900. There isn't a similar alternate part number that would work. view full answer...
The best option to install a Class 3 trailer hitch receiver below the rear bumper of your 2007 Fleetwood Highlander Avalon is the Curt Adjustable Trailer Hitch Receiver # C13701. This hitch offers a 2" drop and will work on trailer frames between 18" - 51" wide. The reason I recommend this hitch is due to it mounting to the frame of your trailer to give additional strength.
Another option is the Curt RV Bumper 2" Trailer Hitch Receiver # E-100 which will mount to your rear bumper as long... view full answer...
What you have is a ducted Coleman AC unit with a heat pump, so you'll need to replace the whole unit, including thermostat because there isn't a plug-in option for this unit. To replace your ducted unit and get a new thermostat you'll need to go with the Furrion HE:
- Furrion Chill HE RV Air Conditioner System # FR55PV
The # FR55PV is a 15,000 Btu like you wanted for better cooling, comes with the thermostat, and has a built-in start capacitor for a power boost so it always starts up.... view full answer...
For your 2020 Fleetwood Bounder we have the SumoSprings kit part # SSR-187-54-1 which is a fit and would work great.
I attached an install video for this kit on a similar 2019 Bounder for you to check out. view full answer...
In order to reduce the jolting feeling in your steering you are going to want to add a steering stabilizer like the Roadmaster Reflex Steering Stabilizer part # RM-RSSA. The Reflex Steering Stabilizer contains a tempered steel spring that will work to return the steering wheel back to its normal state while turning therefore reducing the jolting feeling. The only issue that you are going to have is that they do not make a bracket kit specifically for the V10 model, just the V8 model. However,... view full answer...
The 12 volt accessory circuit of your 7-way can put a maintenance charge on your deep cycle battery. Not enough to significantly charge it but it would keep a fully charged battery topped off. For a more significant charging option the Redarc BCDC part # RED96FR is more optimized for charging and would be your best option. view full answer...
For your 2017 Fleetwood Bounder 35K we have the Air Lift kit part # AL57344 as a confirmed fit for the rear axle and part # AL88240 for the front.
Then for a compressor kit the Air Lift WirelessAIR Compressor part # AL58WQ would work great as it can independently control the front and rear bag pressure and uses your phone to control everything. view full answer...
I recommend the Camco UltraGuard Pop-Up Camper Cover, # CAM45763 for campers that are 12'-14' in length. This will be a snug fit in the width but have extra length. Simply cinch the fabric in on the ends for tight fit all the way around. view full answer...
Terry brand trailers ceased operations after the 2009 model year, so unfortunately it's not possible to contact the manufacturer. I was unable to find anything online regarding the original tire size, but the manufacturer typically put that information on a sticker along with the VIN and the GVWR. This sticker is typically placed either in one of the storage compartments that are accessible from the exterior of the trailer or on the inside of one of the kitchen or storage cabinet doors... view full answer...
Due to the age of your Kwikee steps you most likely need the Pre-IMGL Module part # LC379606 since this is the module that was used for on the steps between 1999 and 2005. view full answer...
Using your rail number as a reference I was able to determine that the Power Gear setup you have is the 523900 so for a replacement motor you'd need the part # LC368417. view full answer...
With your Fleetwood Bounder being a 2004, I was unable to find out if it did or did not come with factory sway bars. However, this does not mean they cannot be added if there are no factory ones, or upgraded if there are. With that said, let's get into it. As a side note, all of these are designed to fit the 35E Workhorse W22 and are American made.
To start, we have the Roadmaster Rear Anti-Sway Bar # RM-1259-109. This has a 1-3/4" diameter and will be more robust than factory sway bars.... view full answer...
The hand rail with the largest handle would be the Stromberg Carlson # AM-533 you'd looked at. The hand rail also features a padded handle on the lower end of the bar for a comfortable grip when you're climbing that first step.
I have no way of knowing what hole spacing was used for the handrail on your motorhome, the manufacturers don't keep track of that information so there's no way to look it up. However, I've provided a photo showing how the mounting holes are spaced for you. Each... view full answer...
Your Atwood GE16EXT water heater looks to have a 17-3/4" tall x 18" wide door, so what you'll want is the Furrion RV Tankless Water Heater - 18" x 18" Door # FR68SR.
This won't be an exact fit as you'll likely have to make some small trims to get the ever-so-slightly larger door in place, but it's the closest option for a water heater. Also note the # FR68SR requires a space measuring 12-3/4" wide, 12-5/8" tall, and 23-1/2" deep. It's narrower and shorter than your Atwood, but does need... view full answer...
We have what you need.
Adco Olefin HD All-Climate + Wind RV Cover for Class A Motorhome - Up to 37' Long - Gray # AD74ZR.
This is an all climate heavy duty storage cover. It will work in the desert or the artic and everywhere in-between.
It will block UV rays, beads water on contact, has built in vents to help prevent billowing in the wind. The fabric will breath to let moisture out and prevent mold and black streaks.
I also recommend getting something to help with the long term odors... view full answer...
For the light switch plates, we have the Single RV Switch Faceplate # 37212845 and the Double RV Switch Faceplate # 37212875 that are white. We have the Single RV Switch Faceplate # 37214045 and the Double RV Switch Faceplate # 37212885 that are black.
In regard to the hub cap covers, it looks like your 2004 Fleetwood Revolution 40 has 8 lug wheels on the rear according to my research. If your rear wheel bolt pattern is 8 on 275mm, then the Phoenix # PXQ822R will work. If your wheels... view full answer...