Light Switch Plates And Hub Covers For 2004 Fleetwood Revolution 40 RV

Question

Question:

Two Questions: 1 Need Center hub cap cover for 2004 rear dually Fleetwood Revolution 40 Diesel pusher. 2 Light switch plates

asked by: Dave L

0

Expert Reply:

For the light switch plates, we have the Single RV Switch Faceplate # 37212845 and the Double RV Switch Faceplate # 37212875 that are white. We have the Single RV Switch Faceplate # 37214045 and the Double RV Switch Faceplate # 37212885 that are black.

In regard to the hub cap covers, it looks like your 2004 Fleetwood Revolution 40 has 8 lug wheels on the rear according to my research. If your rear wheel bolt pattern is 8 on 275mm, then the Phoenix # PXQ822R will work. If your wheels are actually 10 lug, then the Phoenix # PXQH1002R will work for 10 on 225mm bolt pattern. The Phoenix # PXPQH1401RHC will work if your rear wheels are the 10 on 335mm bolt pattern. If you have a different bolt pattern, feel free to give me the exact bolt pattern of your rear wheels and I can help you find the replacement hub cover.

I have attached videos for these products so that you can fully understand the features and fitment etc.

expert reply by: Andrew N

0

Answer 1

We do offer the RV Switch part #37213075 with a bezel as the Single Rocker Switch part #37212005.

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Your math is correct in your trailer weight load example. If a fully-loaded tandem axle trailer weighs 4000-lbs then each of the 4 tires will bear 1/4th of that load, or 1000-lbs. In this case a tire rated for 1300-lbs would provide a good safety…

view full answer...

Answer 9

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 10

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Light Switch Plates And Hub Covers For 2004 Fleetwood Revolution 40 RV

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching