Unfortunately since these mounting kits are not only specific to the grille guard they are also specific to the vehicle as well.
That means you can't just swap the grille guard over between vehicles, you'd have to get a new grill guard and that would come with the correct mounting hardware.
For instance, if you had the Westin HDX Grille Guard with Punch Plate - Black Powder Coated Steel # 57-3975 then the correct mounting hardware is the Replacement Mounting Hardware Kit for Westin HDX... view full answer...
We recommend using a weight distribution hitch whenever the trailer weight is more than 50 percent of the tow vehicle's weight of if you're experiencing sway or sagging issues.
If you need a weight distribution shank, like the Curt # C17124, I've linked our selection for 2 inch hitch receivers for you. view full answer...
We do indeed have the exact bearing kit you need for your Lippert 5,200 lb axle, which is the following:
- Bearing Kit # BK3-300
This comes with the correct bearings, races, and grease seal for your 5,200 lb axle. If you also need a bearing packer and grease, I recommend the Powerbuilt Deluxe Bearing Packer # ALL647646 with the Trailer Wheel Bearing Grease # L11390. view full answer...
We have several 5th wheel bracket/rail kits that would work for your 2017 Ram 2500 to install your Curt item # 16055 gooseneck plate adapter, but I'd recommend the Curt # C16427-204 as the least expensive alternative. The bed rails provided with the kit are industry standard, so they'd be compatible with your item # 16055 plate.
If you don't have a 7-way mounted in your truck bed, you can install one using part # C56000.
I'll link to install videos for the rail kit and the 7-way harness... view full answer...
If you're planning on using the B&W Companion 5th Wheel Trailer Hitch w/ Slider # BWRVK3400-5W then you're going to need the Custom Underbed Installation Kit for B&W Companion 5th Wheel Trailer Hitches # BWGNRK1384-5W to be able to install this hitch in your 2017 Ram 2500, no pucks needed.
However the only real drawback with using this hitch is that if you want4ed to use a different hitch in the future you couldn't due to the way this hitch mounts.
You could still use the B&W Patriot... view full answer...
The only sliding fifth wheel trailer hitch we currently carry that fits directly into your 2018 Ram's puck system is the B&W Companion, part # BWRVK3670. You won't need an adatper at all.
B&W is often regarded as the top of the line in fifth wheel hitches because of their strong jaw-to-kingpin contact with 1 inch thick jaws that wrap all the way around the trailer's kingpin. The slider offers up to 12 inches helping you with clearance in your short bed Ram.
I've linked a demo video... view full answer...
The replacement parts that you are needing are in the kit # RP94316. This includes the wear plate, wedge fasteners, wear bushing, wear disc, turret tube fasteners, lube, and instructions. The washers that are included in this kit are the conical washers. view full answer...
It sounds like the installation kit is the Reese universal kit # RP30035. To use it on your 2012 Ram 2500 short bed you would need to add bracket # RP58186. You will also need new hardware # 58164 since the bolts are not meant to be used more than once. You can reuse the other brackets and the rails.
Installation is not all that difficult, just time consuming. To see if this is something you want to tackle yourself I have included links to the installation instructions to the right. I... view full answer...
Equal-i-zer Weight Distribution Shank # EQ90-02-4900 fits into a 2-1/2-inch hitch like # C15801, so it is not a good choice for use with the Pro Series weight distribution system # PS49582. If you want to use this 2-inch system in a 2-1/2-inch hitch you can add a reducer sleeve # C45405 to drop the receiver opening size down to 2-inches. view full answer...
When it comes to installing a gooseneck hitch on your 2013 Ram 2500 crew cab The B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit - 30,000 pounds # BWGNRK1320 is not confirmed to fit, but The B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit - 30,000 pounds # BWGNRK1313 will fit. There is different mounting points on the 2013 given why # BWGNRK1320 will not fit. The towing capacity, and the vertical load limit are the same.
I attached... view full answer...
Aside from the part number of the Jack-It 2 Bike Rack for A-Frame Trailers # LC429756, the only other part number mentioned is the cable lock CAB-10. This was rebranded as an etrailer cable lock and can be found now as part # e98891 on our site.
Some additional accessories we have for the Jack-It are the Bump-It # LC723359 adapter for a standard hitch receiver and the Straight Shank # LC67HD if you want to avoid having the bikes directly above your propane.
If you are looking for something... view full answer...
If you have the factory gooseneck prep kit in your 2016 Ram 2500 then you'll have holes in the truck's bed that safety chain loops and hitch ball included with part # RP30140 fit into. I've attached a picture of what they look like installed and if you have the locations for them you can't miss them. If you have the factory kit then # RP30140 is all you'll need.
If you don't have the factory kit then you'll need to install a gooseneck underbed trailer hitch like the Curt # C60614. This... view full answer...
For your 2020 Ram 2500, you can use the Curt Custom Fifth Wheel Installation Kit for Ram Truck # C16427-204 to install your Pullrite 2700 Series Super Slide 5th wheel hitch.
This is a custom installation kit for your truck, that requires no drilling, and will mount using the existing holes on your frame.
This kit also includes all the needed installation hardware, frame brackets, and base rails. view full answer...
Any standard 5th wheel hitch like yours will work with industry standard above bed base rails. The Reese Quick-Install Custom Base Rails and Outboard Installation Kit # RP56009-53 will work well for you.
The custom installation kit will bolt to pre-existing holes the frame of your 2015 Ram 2500, and the outboard brackets will allow installation to be much easier than more traditional inboard installation brackets.
If you need an in-bed wiring harness and trailer connector for your pickup,... view full answer...
The correct slider base for your B&W Companion on your 2016 Ram 2500, is the Replacement Slider Base for B&W OEM 5th Wheel Trailer Hitch # BWRVB3670.
This slider base will drop right into the pucks on your 2016 Ram 2500, and will work with your current B&W Companion. view full answer...
Though we do not have The Reese Elite Series Underbed Gooseneck Trailer Hitch w/ Rails and Installation Kit - 25,000 pounds # RP30158-52, we do offer The B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit - 30,000 pounds # BWGNRK1320.
The B&W system will give you the removable gooseneck ball that can tow up to 30,000 pounds, and will give you complete truck bed access when you're not towing. It has a simple installation with the included custom mounting kit,... view full answer...
I recommend the Edge EvoHT2, part # EP86040, for a chip tuner to improve your gas mileage by choosing a pre-loaded tune.
The Edge Insight CTS2, part # EP84130 that you asked about, will not directly improve your gas mileage since it is not a programmer but a monitor. It can be used to help you adjust your driving style and improve your mileage since you can monitor the mpg of your truck. Then you can use the info from the monitor to develop fuel saving driving habits. view full answer...
Typically with truck beds that are shorter than 8 feet a sliding hitch is going to be required in order for you to make 90 degree turns; there are some trailer designs that sometimes allow for enough clearance but I don't believe that the tapered nose on your 2021 Grand Design Reflection 311BHS falls into that category. However, if you want to take some measurements of your truck and trailer, you can put them into the formula below and determine if you're going to have enough space to make... view full answer...
I've linked our selection of weight distribution shanks for 2-1/2 inch hitch receivers.
Most shanks are universal and will work with other brands of systems. As long as the holes are 3/4 inch in diameter and are spaced 1-1/4 inches apart they're interchangeable. Whether it's a shank for a 2 inch hitch or a 2-1/2 inch hitch the holes are normally the same.
I've also attached an article to help you determine how much drop you need in case you don't already know. view full answer...