The Brophy Camper Hold Downs, Part # HSSF, install without drilling and use the included padded T-bar hardware to evenly distribute forces downward and inward toward the inside of the truck bed. The top rail itself bears only some of the load from the tie-down points since most stress is distributed to the inside of the bed.
I have attached the installation instructions for this item for your review.
You will want to review this part for compatibility with your specific year/make/model... view full answer...
Stromberg Carlson 100 Series 5th Wheel Tailgate with Open Design for GM Trucks Item # VGM-07-100 has a 100 lb max weight capacity. However you can get a hitch extender and not replace your tailgate. As long as the extender sets your ball mount past the edge of your tailgate you will have enough clearance for the jack.
I recommend Brophy Hitch Extender with Step for 2" Trailer Hitches - 18" Long Item # RST18 if you have a 2" hitch on your truck. When used with weight distribution it gives... view full answer...
The side to side pivoting of the Curt A30 # C66HR head is to help with coupling to the king pin of the trailer and slightly help with ride quality since it has built in rubber dampeners. This should not cause any issues while hauling your Shipshe car hauler trailer. view full answer...
While there are steps you can use for a pickup truck, electric trailer steps cannot. Instead, there are options such as the Carr Custom-Fit Side Steps # CARR125001 which fit certain model year Ford trucks, or you can use running boards or nerf bars.
I have added a link below to our entire selection of steps, running boards, and nerf bars for you to check out, or if you let me know the year, make, and model of your truck I can make a recommendation for you. view full answer...
According to Truxedo, before changing the rear header, you'll want to first check that the tonneau is correctly positioned on the truck. If the cover is situated too far toward the front of the vehicle, it will not latch correctly no matter what's replaced, so you'll want to refer back to the original installation instructions to ensure that the cover is installed correctly and that the gaps are as they should be.
If the cover is indeed positioned correctly, and replacing the latches didn't... view full answer...
This question has come up before. In order to make the drawbar portions of the tie downs, TorkLift would need to do a special manufacturing run for just that particular item. This would considerably add to the cost of the product, which would end up costing you about the same amount of money, if not more as starting from scratch would.
Given this, I'd recommend simply starting from scratch. If your truck does NOT have running boards or a side step that extends under the bed (wheel to... view full answer...
Yes, the price you see for the TorkLift Custom Frame-Mounted Camper Tie-Downs - Front # TLD2142 is for the pair of front tie-downs.
Note: This tie-downs are a compatible fit for a 2019 Ram 3500 with an 8 Foot Bed - with board or step extending under bed and with a factory installed hitch or a TorkLift SuperHitch Magnum 30K.
If you need help finding the correct camper tie-downs for your application I'll just need to know the length of your Ram's bed, whether or not there are running... view full answer...
There is a difference in price between the steel TorkLift Custom Frame-Mounted Camper Tie-Downs and the ones that are made from aluminum that fit your 2019 Ford F-250 Super Duty with a 6-3/4 foot bed, no boards or steps under the truck bed and either the factory hitch, SuperHitch Original 20K or SuperHitch Magnum 30K.
You can find the prices on the individual product page, and to convert that to Canadian money you will need to use your favorite conversion source; I'll also send a link... view full answer...
MOryde's pin box cushioning wouldn't work with a rotating pin box like their You Turn line since the wear pads would constantly be engaging every time you went to make a turn and would delay the pin box from rotating since there would be slack to go through before the force would start pulling the pin box to either side.
The only cushioning you'll see for rotating pin box is typically going to be an air spring inside the pin box to help deal with up and down motion, like part # RP61412... view full answer...
The cargo management rails that our truck bed bike rack selection guide is referring to are side-rails that are installed on the inside of the truck bed frame rails. With these internal side rails installed you can add cross bars which will then give you two layers of cargo carrying ability. These rails are typically dealer installed and are not offered with all makes and models of trucks. I could not find where Toyota has these rails however this is an option on Ford trucks and Nissan... view full answer...
The TorkLift Custom Frame-Mounted Camper Tie-Downs Front # TL44FR is the TorkLift part number C2226. The Rear # TL84FR is the TorkLift part number C3222. These are the correct parts for your 2023 Chevrolet Silverado 3500 Long Bed Dually with the factory receiver and no steps/running boards under the bed.
I recommend using the TorkLift Locking FastGun Turnbuckles # TLS9529-2-LK to secure your slide in camper on your Silverado. These have a stainless steel construction with black powder... view full answer...
Yes, there is a difference in hitches for an 8' bed on your 2022 Chevrolet Silverado like the B&W Companion # BWRVK3710, which is a fixed hitch. Fixed hitches are used primarily on long bed trucks, and sliding hitches like the Demco Hijacker # DM8550034 are used short bed trucks. The reason being is because, due to the shorter bed length, the hitch is installed closer to the cab, reducing the turning radius significantly, whereas, the long bed trucks install the hitch farther from the cab,... view full answer...
I spoke to my contact at Reese and they confirmed that some front-to-back play, such as what you are experiencing, is normal with your 5th wheel hitch.
Since you have a factory-installed under-bed rail system in a recent model year truck we will assume that the 1/4 inch front-to-back play you have noted is not due to those components being loose or worn. It is possible that some minor adjustments to the installation may help. You can re-check this if you like.
You can re-check that the... view full answer...
I see you got the RockyMounts LoBall Bike Rack for Truck Bed # RKY1097. We do not have a kayak or surfboard carrier that mounts in the truck bed like the RockyMounts.
If you are not installing a roof rack to carry the kayak or surfboard we do have a way to carry them in the bed of your truck. We carry tailgate pads like part # SR26457 for full-size and part # S64761 for mid-size trucks. These are pads that are attached to the tailgate and you then carry the board or kayak as shown in the... view full answer...
A lockable hitch pin is included with the HitchMate Extendable TruckStep # HE4045 so you can be free of worry that someone will try to steal it from your hitch receiver. Just add a padlock with a 3/16-inch diameter shackle, such as # 131D. view full answer...
Turning clearance is always going to be best with a long bed truck. Trucks with long beds are more designed for towing, and there are less of them on the market today because more people are buying trucks for reasons other than towing. If I were choosing a bed length to tow a 5th wheel camper, I would definitely go with a long bed because it will most easily offer sufficient turning clearance.
Some 5th wheel campers have a nose that is specially designed to work with short bed trucks.... view full answer...
To determine the size of your truck bed, you will want to measure the inside of the truck bed from front to back. Most accessory companies round off their measurements to the nearest half-foot so your measurement may not exactly match the options that we have listed.
The GM Cargo Management System is a rail system which runs the length of the bed sides and behind the cab.
The BedRug Custom Full Truck Bed Liner, # BRC07CCK, that we offer is made to fit a 5-1/2 foot bed without the Cargo... view full answer...
I have a great ladder rack option for your 2022 GMC Sierra 2500 with standard bed and no cover. The Buyers Products Over-The-Cab Truck Bed Ladder Rack # 3371501150 is a great option for a work truck. This ladder rack is an over-the-cab ladder rack with removable rear crossbar that lets you carry ladders and lumber on the rack while hauling appliances and furniture in your truck bed. It also features raised side rails that provide load support for your cargo and multiple cutouts that can... view full answer...
Sure, if you have cargo tie-down points in your truck bed you can just strap down the etrailer Cargo Bag w/ Mounting Straps # 988501. view full answer...
Go To Results