I cannot locate an order for the etrailer Replacement Tow Bar Adapter Kit # e98978, but I do see that you have the etrailer XHD Non-Binding Tow Bar for Blue Ox Base Plates # e67ZR which already includes the Tow Bar Adapter Kit # e98978 installed. Not sure if that is the one you meant, or if you are trying to add an additional adapter thinking it is needed.
The two prongs on the Blue Ox Base Plate Kit # BLU23XR should fit inside of the 3 prongs on the Tow Bar Adapter Kit # e98978 on your... view full answer...
We actually have a version of the # ETBC7 that we put together specifically with the Curt Echo Mobile brake controller part # C51180 in mind with the # ETBC7L which comes with just the components needed for the Echo.
The ETBC7 comes with the same components plus additional ones that you won't need but if you have it already it can still be used. I attached install instructions and install video links to this page for more info as well. Basically your 4-way plugs into the adapter and then... view full answer...
No, the Custer Wireless LED Tow Bar Light # LIW-LDTL-7B would have to be in the motorhome 7-way in order to receive the traffic signals from the motorhome and send them to the light bar. If it was in the towed vehicle you wouldn't get a signal at all since the vehicle isn't running and sending anything to the 7-way.
The Blue Ox Patriot # BLU37TR would get its power from the battery of the towed vehicle. In most vehicles the 12v outlet loses power when the vehicle isn't running so you would... view full answer...
Yes, installation of the Curt # C67JR will require bumper/fascia removal on your 2024 Subaru Outback. The hitch bolts on behind the rear bumper beam. view full answer...
In regards to the RockyMounts Hitch Extender LS part # RKY10011, the hitch pin has to be inserted from the passenger side for the anti rattle to engage. That said, you should be able to simply turn the extender upside down so that the hitch pin is then inserted from the driver side. view full answer...
The fact that you do not have holes on the frame of your 1989 Ford Bronco is not a problem. You will drill holes into the frame to install this Curt Hitch # 14001 on your vehicle.
The location of your spare tire will not be a problem either, check out the installation instructions I attached that show how it installs. I also attached an installation video for this hitch for you to check out.
At most you have to reposition your spare tire, but that would be the worst case scenario.
To... view full answer...
To replace the fenders on your trailer with the Fulton black trailer fenders, # F008585-2, you will need to either reuse the old hardware or you will have to fabricate some hardware. If the old hardware cannot be used, a visit to a hardware store will provide you with the parts to fabricate something that will work. view full answer...
The Westin bumper bracket kit part # 95600 does fit the 1996 Ford Bronco and is normally used to install a Westin Fey Surestep part # 21002-95600. view full answer...
It really doesn't matter where you install the Reese Friction Sway Control Kit # 83660, you'll just want to install it on fairly level ground. If you installed it on a hill where the trailer was at a different angle than the tow vehicle then it would affect the effectiveness of the friction bar and either be too tight or too loose. Luckily this style of sway control is very easy to install and adjust by simply turning the handle. view full answer...
I reached out to Curt about this and they said the power wire for the # C42WR must run directly to the battery. It would be really convenient if it worked with the auxiliary switches, but you would potentially blow the fuses and cause other problems with your 2023 Ford Bronco if you installed it that way. view full answer...
The width of the base rails on the TracRac SR # TH43002XT-781 ladder rack is 4 inches wide. I went ahead and attached a diagram that shows this specification to give you better perspective. view full answer...
The Furrion Chill HE RV # FR67FJ does not have Bluetooth it is wired. So one of the four prong connector cables would run from one AC to the other AC and then from there, would run to the thermostat.
I've attached a wiring diagram of this provided by Furrion for you to check out as well. view full answer...
It could be, however there isn't going t be a way to determine if that's the correct wire based off of the color.
In order to find the correct brake signal wire behind the dash on your car, you're going to need to use a circuit tester like part # PTW2993.
Then you will need to press the brake pedal in and test each of the wires running to the brake pedal in order to determine which wire only illuminates when the pedal is pressed.
This will be the correct brake signal wire you will... view full answer...
There unfortunately isn't a plug-and-play wire harness to connect your Hayes Syncronizer Trailer Brake Controller # HA81725 to your 2023 Ford Bronco so you'll have to use the universal splice-in wire harness # HA81789-HBC. This harness will need to be wired in the follow order:
Black: 12v power
White: Ground
Blue: Trailer brake output
Red: Bronco cold side of Brake Light Switch
If your Bronco is a base model without the signature LED lighting then the cold side of the brake light switch... view full answer...
There isn't a diagram available specific to the Tekonsha PowerTrac Brake Controller # 39523 but it uses standard brake controller wiring. The black wire is for 12V power to the controller, the red wire is for brake input from the vehicle and it gets connected to the cold side of the brake light switch (the wire on your vehicle that ONLY gets power when the brake pedal is depressed), the blue wire is for brake output to the 7-Way connector, and the white wire is for ground.
I have attached... view full answer...
It's possible that the trailer connector on your 1991 Ford Bronco was added aftermarket and not all the functions were needed so one was not installed. You can check the functions of the trailer connector using a circuit tester such as # PTW2993 if you do not already have one.
You can follow the diagram I have included here. Ignore the colors and test the pins on the connector for function. That will show you what is present and what is missing. Once we know which function is not present... view full answer...
Per the instructions also included below, you would mount the Aries Round Nerf Bars # AA203038 with the following steps 2-6. The instructions also have the pictured examples/figures for reference. Included is also a video review for reference.
"Select the passenger sidebar from the list of parts & attach the front mounting bracket to the front leg of
the sidebar with (4) 10mm hex bolts,(8) 10mm flat washers,(4) 10mm lock washers & (4) 10mm nuts as
see in (FIG 1) offset portion of bracket... view full answer...
At this time we have not had he chance to video a brake controller installation on a 1996 Ford Bronco.
I do have some information that will be helpful though. If your Bronco has a factory 7-Way connector at the rear of the vehicle or if you have a factory tow package there will be a plug along the left frame rail behind the rear bumper. If this plug is present then you can look for a brake controller connector under the dash above the transmission hump. This connector will match up to... view full answer...
The spring bars you'll need to use will depend partly on your total tongue weight, as well as the weight capacity of the bars.
If your tongue weight is somewhere in the 500-600-lb range, then the better option would be the Replacement Spring Bar for Curt MV Weight Distribution System # C17071 like you mentioned.
However if the tongue weight range is in the range of 800-1,000-lbs then the:
-Replacement Spring Bar for Curt MV Weight Distribution System # C17073 like the ones currently... view full answer...
I spoke to my contact at Rampage and installation of the Rampage Safari Island Topper, # RA98235, is pretty basic so they do not have written instructions available but I can run through the steps for you.
The Rampage Safari Island Topper, # RA98235, connects to a front header / windshield channel, like part # RA98499, and then following the factory roll bars, the straps at the back will pull down and wrap around the rear roll bar. view full answer...
Go To Results