The Camper Hold Downs, # HSSF, are a universal fit item that will fit most full size trucks. This should include your 1969 Ford F-250. In order to be sure, take a look at the last 2 pictures on the product page. These pictures show the dimensions of the hold downs so you can compare them to your truck bed. I have also included a picture that is actually the instructions. You can click on it to make it larger.
If you determine based on the dimensions and instructions that these hold downs... view full answer...
To install the Detail K2 Rampage II Snowplow # K2RAMP8219 you only need add Custom Mounting Brackets # K281516. The brackets install directly into your F-250's frame so as long as the lift kit on your truck does not have any interference with the frame the brackets will work.
These brackets are a fit for a 1983 Ford F-250 4 wheel drive, bolting onto your truck's frame. Those are the only two items you will need to assemble and plow snow. view full answer...
If your 1973 Ford F-250 is not a dually and has bedrails that are not more than 5.5" wide and the space between the lip of the bedrail and the wall of the bedrail is at least 2" wide then the Brophy Clamp On Camper Tie-Downs # HSAB will work for your vehicle. These tie-downs will clamp onto the bedrails of your truck to provide you with attachment points for your truck bed camper. You'll also need some turnbuckles # TDHP to properly mount the camper to your tie-downs. view full answer...
The Camco Automatic Changeover part # CAM59005 will replace your marshall brass co model 240 without a problem. We do not carry the marshall brass co models but from what I could tell from my research they are just standard manual dual regulators. I was not able to find a BTU rating on the 240.
The Camco Automatic Changeover part # CAM59005 will automatically switch tanks for you when one is empty. view full answer...
The B&W Trailer Hitch # BWHDRH25122 is a confirmed fit for a 1970 Ford F-250 pickup with a standard or step bumper, regardless of if it is a 4WD or 2WD, and is designed to allow fits for both 34 and 37-1/2 inch frames. view full answer...
The Draw-Tite Trailer Hitch Receiver # 41504 is a custom fit hitch for specific trucks. The trucks it fits have a frame spacing of either of 34 or 38 inches.
Since you're going to need something more universal for your 1949 F3 you may like the Curt # C13701 that fits frames between 18 and 51 inches wide. Or if you can tell me the width of your truck's frame, center on center, I can wee if we have other options available. view full answer...
Technically you could use RV hitch # 5350 on your 1972 Ford F-100. This would likely require drilling holes into the truck frame though. Otherwise I do not see a reason why it wouldn't work for you. We even had a customer put it on a 1957 Ford. So this hitch gets around but in a good way.
I also recommend ball mount kit # EBMK4 which comes with a ball mount with a 2-3/4 inch rise or 4 inch drop, interchangeable ball set, hitch pin with clip and a storage bag. If the ball mount does not... view full answer...
The Draw-Tite Max-Frame Trailer Hitch # 75034 actually mounts to the underside of the 1966 Ford F-100 frame so since it looks like your gas tank is completely inside the frame you'll be able to mount the trailer hitch.
I took a trip out to the warehouse for a few different dimensions I thought you might like since it looks like you're doing some modifications. The crosstube of the trailer hitch sits roughly 2-3/4" below where it mounts to the frame and then the closest edge of the crosstube... view full answer...
We do have a solution for you, though the Reese Trailer Connector Adapter # 78118 will not work for you.
Instead I recommend the Hopkins Endurance Quick-Install Trailer Connector Adapter # HM47200 which will plug into your truck's 4-way and allow you to connect your trailer's 7-way. view full answer...
I checked with B&W and the Class V B&W Heavy-Duty Trailer Hitch # BWHDRH25122 is a confirmed fit for the 34 inch frame on your 1973 Ford F-350 that has a 10 inch step bumper.
The only thing you may need to do is remove or modify the spare tire carrier (if your truck has one) in order to ensure there is not interference with the hitch.
I have added a link to the installation instructions of this hitch for you to check out as well. view full answer...
We do have hitches available for your truck (see link) but none of them are designed to fit behind the tag (license plate). At this time I do not know of a Hidden or Stealth hitch that is available for your truck.
For a trailer hitch that would sit below the rear bumper, I recommend looking at the Draw-Tite Class III Trailer Hitch, # 75034. This hitch will fit as long as you have the standard or step bumper.
If you have a deep drop bumper, then you will want part # 41504. view full answer...
The Installation Kit # 92230 is the kit you need to install one of the Westin Fey Surestep Bumpers # 20022, # 21002 or # 21007 on your 1973-1978 Ford F-250. view full answer...
A high boy is a generic term used to encompass all Ford F-250 4x4 trucks from the late 1960s to the late 1970s (circa 1967 to 1977 and a half). If your 1976 is an F-250 with 4 wheel drive, it falls under the high boy umbrella. F-100 and F-150 models are not considered high boys even though 4 wheel drive was an option for some.
The high boy trucks came with a different transfer case (what is called a divorced transfer case), the front cross member set up was different, and they sat higher... view full answer...
From the picture that you sent in it looks like your vent cover has a continuous hinge. If that is the case then you just need to confirm that it measures 14" x 14".
If it does meet those requirements then the Replacement Lid for Elixir RV Roof Vent # CAM40156 will fit!
You could also use the metal Replacement Dome Assembly for Ventline Ventadome Trailer Roof Vent # BV0534-00 or the Smoke Replacement Lid for Ventline and Elixir RV Roof Vents # CAM40148 as well depending on what you are... view full answer...
The Curt Class IV Receiver Hitch, # 14001 is designed to fit the wider framed 1978 Ford F-350 trucks, and will not fit on the 34 inch wide framed cab and chassis models. I went out to the warehouse and measured the Curt hitch, # 14001 and the installation holes are 36 inches apart on center, see attached photo.
The correct Curt Class IV Receiver Hitch for your 1978 Ford F-350 is part # C14082, which is designed to fit the cab and chassis models with narrower 34 inch frame, see instructions... view full answer...
Yes, the Curt Class V trailer hitch you referenced, part # C15300, is a confirmed fit for your 1979 Ford F-150 long bed with standard or step bumper and 37-1/2-inch wide frame. Installation will require some drilling and temporary removal of the spare tire. An install video is linked for you.
For a wiring harness you can use Draw-Tite # 18252 which provide a 4-pole flat trailer connector for your trailer lights.
A great option in a ball mount kit is item # EBMK2416 which includes a ball... view full answer...
The Adarac Aluminum Series Custom Truck Bed Ladder Rack # A4001221 is a very nice system, though we simply sell them and do not actually produce them. They are custom-made to fit certain year, make and model of truck, and though unfortunately there are none which are going to fit your 1964 Ford F-250, but we do have an option for you.
The Yakima Outdoorsman 300 Ladder Rack # Y01137-Y00410 is a clamp-on installations that will work with your truck and provide you with a way to carry cargo.... view full answer...
Pace Edwards doesn't have an UltraGroove that will fit your 1976 Ford F-150, but the Pace Edwards JackRabbit Retractable Hard Tonneau Cover w Explorer Rails # 311-JEF1290 will still give you the T-Slot rails that you were interested in.
These T-Slots will allow you to install a large variety of accessories including Thule or Yakima ladder racks, crossbars, Kayak carriers, bike racks, etc.
One of the most popular Kayak carriers we carry is the Thule Hullavator Pro Kayak Carrier and Lift... view full answer...
You're in luck because there are custom mounting brackets for a snow plow that fit your 1976 Ford F-250 (so long as it is not a SuperCab model), the Custom Mounting Brackets for Detail K2 Snowplows # K281501. These mounting brackets work with the following snow plows:
- Detail K2 Summit II Snowplow # K2SUMM8826
- Detail K2 Summit II Elite Snowplow - Electric Actuator # K2SUMM8826ELT view full answer...
I've checked the hitches and while none of them actually come inside of the frame rails the Draw-Tite Max-E-Loader Trailer Hitch Receiver part # 41004 will offer the most clearance of the three options you have mentioned. view full answer...
Go To Results