To install a 7-Way harness on your 2023 Ford Bronco you will need two separate wiring harnesses because they don't make just one that'll do the job.
The first harness you'll need is the Curt T-Connector Vehicle Wiring Harness item # C87BR. This custom-fit T-connector plugs into your Bronco's wiring harness, which is located behind the incandescent tail lights. This will provide you with a 4-flat connector.
The second harness you will need is the Universal Installation Kit for Trailer... view full answer...
I went ahead and reached out to my contact at Adco, and he confirmed that the dimensions of the Adco Olefin HD All-Climate + Wind RV Cover # AD89ZR is 44' long x 8.8' wide x 11' high. view full answer...
The trailer axle over-under kits we offer are made for 2-3/8-inch or 3-inch diameter axles. Kit # K71-384-00 fits a 2-3/8-inch diameter axle and kit # K71-385-00 fits a 3-inch round axle. The axles do not have to be branded Dexter to use these kits, but they do need to have the matching diameter so that the u-bolts fit.
Each one will lift the trailer by the sum of the leaf spring stack height plus the axle diameter. So a trailer with 3-inch axles and with a 2-inch tall spring stack will... view full answer...
Yes the Reese Electric 5th Wheel Landing Gear Set - 36" Lift - 8,000 lbs, # RP500708 will work for your application. It can be used with a trailer that weighs more than 8,000 lbs because it is only supporting a portion of total load, the tires, wheels, and axles are supporting most of the weight. The pin weight of a 5th wheel trailer is approximately 20% of the loaded trailer weight.
The measurement from inside of top weld stop to inside of bottom weld stop is15-1/2". The measurement... view full answer...
The Kenda Karrier # AM10303 would be a good tire for you. The main thing that you want to consider is the weight of your camper. These tires are rated for 2,830 lbs at 80 psi. You may have had this same rating of tire before from factory, but with 4 of these tires you are below the GVWR of 12,370 lbs.
If you are loading your camper to its fullest capacity you may want to go with a tire that is rated for more weight. If they will fit your camper, the Provider ST235/85R16 # A16RGBML would... view full answer...
I measured the Swagman E-Spec Bike Rack for 2 Electric Bikes part # S94FR for you and the distance from the center of the hitch pin hole to the center of the first wheel tray is about 16". view full answer...
The brake pads on the 12" Dexter Electric Drum Brake Kit # 23-180-181 are 3/16" thick. Dexter Axle recommends replacing them once they get down to 1/16" thick. view full answer...
The Andersen Ultimate Connection 5th Wheel Trailer Hitch System with Adapter # AM3200 height is from the top of the hitch ball without adapter to the top of the base rails...not the bed.
Height adjustments: (measured from top of rails to top of ball mount)
18" Upper position
16-7/8" Middle position
15-3/4" Lower position view full answer...
Actually, if you scroll down the page a little, there is a photo showing the hole spacing.
The most important measurements are the width (side to side distance between the two bolt holes) as shown in the provided photo as well as the axle spacing. Given your axle spacing, the # K71-652-00 will work perfectly for you.
I've linked to an installation video you might find helpful. view full answer...
If all you damaged was the rotor then you can just replace it with the Kodiak 13" Rotor item # KR1389D.
I didn't get anywhere either with that serial number. However, it looks like your 2020 Keystone Montana 3121RL uses a inner bearing item # 25580 and an outer bearing item # 14125A. The Kodiak 13" Hub and Rotor item # KRH1378D you were looking at is exactly what you need to replace your gouged one if you want to swap out both the hub and rotor.
For replacement brake pads you'll want... view full answer...
The Valterra DWV Adapter for RV Sewer System, # D50-2929, installs into your RV's 3 inch waste valve system. If your tank hub is threaded as such, yes. Note that this is the internal diameter at 3". The outer threaded section is about 3-1/2". view full answer...
Here is an image of the measurement you requested for the Replacement Screen Frame with Screen # BVC0573-41. As the frame design on this is different from your current vent it does appear to be longer at approximately 3-1/8" to the far edge of the screen. view full answer...
The holes that mount to the motor for the Replacement Brushed Chrome Brackets for AirrForce RV Ceiling Fan with Light # 277-000399 do measure 1-1/2" on center just like what you have. I have attached a photo that has additional measurements that you can reference as well. view full answer...
The best cover for your 28' 2013 Keystone Cougar XLite 28SGS 5th Wheel Trailer is the Adco Olefin HD RV Cover item # AD99ZR. This cover will protect your trailer in all climates. The contoured cover conforms to the shape of your trailer and secures with the integrated straps so it won't flap in the wind.
The HD fabric blocks 99.8 of UV rays and the material also beads moisture instead of allowing it to pool into standing water that can damage the cover.
My favorite part about the Adco... view full answer...
I measured the Replacement Blades for AirrForce 42" Hugger Style RV Ceiling Fan # 277-000398 for you and they are 16- 5/8 inches long with 4 inches wide at the bottom and 4-7/8 inches wide at the top. I've attached a photo to assist. view full answer...
We've done some checking on your 2007 Cougar 276RLS model is 29 foot long. An excellent cover choice is the ADCO # 290-52254 AquaShed which works best for short-term storage in moderate climates. Heavy-duty, 3-layer fabric protects against rain, snow, and sun. Contoured fit matches shape of your toy hauler. Secures with cinch ropes and straps with buckles. view full answer...
The TorkLift GlowStep Revolution # TLA8003 measures 7-1/2" between steps and yes, they are consistently all the same. The only way they would not be is if you adjusted the landing gear on the bottom, which you can do to ensure they are perfectly stable on any terrain. view full answer...
The Lippert Alumi-Tread Manual Pull-Out Step - Quad # LC432698 that you referenced does indeed feature a drop/rise of 8 inches, while the Lippert Alumi-Tread - Triple # LC432696 has a drop/rise of almost 9 inchces (8-3/4 inches to be exact).
The 4-Step model will feature an overall distance of 49-5/8 inches from the top of the mounting bracket to the bottom of the last step. The 3-Step model has a distance of 38-3/4 inches for this measurement. The ideal entry height for the 4-Step, which... view full answer...