That's a hard number to give since a portion of the # HM39524 fits under the dash but I can give you the overall dimensions of this and you can compare that to the available space you have to see if it would fit. This measures 19" long x 11-3/4" wide x 6-3/4" tall. view full answer...
The Timbren Rear Suspension Enhancement System # TJRL4 has an overall length of 9.5 inches and is a custom fit for 2002-2012 Jeep Liberty and 2007-2012 Dodge Nitro models. view full answer...
You will need to measure to find out if you will have enough clearance for the Thule Double Track Bike Rack, part # TH990, to clear your spare tire. The distance from the hitch pin hole on the rack to the closest upright portion of the rack that could interfere with the spare tire is 11-1/2 inches.
You will want to measure 11-1/2 inches back from the pin hole on your hitch to see if that distance will clear your spare tire. view full answer...
The distance between the mounting holes that is on the Curt Trailer Hitch # 13044 that you referenced is 37-3/4 inches. This Curt Trailer Hitch # 13044 is confirmed to fit the 2002-2007 Jeep Liberties and should work well for your 2003 Liberty Renegade.
Occasionally during shipment a hitch will get slightly bent, in this situation it is okay to bend the hitch back with a floor jack, vise, or an open stairwell. However, if any visible signs of stress are on the hitch such as creases or... view full answer...
I took a couple measurements on the hitch receivers themselves and compared it to the measurements we made when we installed them on Jeeps to determine if there's a difference. We've installed the Draw-Tite # 75578 on a 2008 Jeep Liberty and the Curt # 13245 on a 2011.
The hitch pin hole of the Draw-Tite on the 2008 lines up perfectly even with the bumper's edge as shown in the video. The pin hole is 2-1/2 inches from the end of the receiver tube per my measurement. So when we combine... view full answer...
Draw-Tite trailer hitch # 75128 for your 2003 Jeep Liberty uses M12 (12mm) bolts that thread into the matching M12 weldnuts inside the frame of the vehicle. The hardware comes with the hitch but if you need replacement hardware for the hitch use # RHK. Just enter the hitch number and manufacturer where indicated on the RHK page to get the correct hardware. I have included a link to a video showing an example installation for you. view full answer...
I checked with my contact at Roadmaster, and the High-Low hitch adapter # RM-048-6 measures approximately 5 inches from the center of the hitch pin hole to the angle bracket, which would be the first point that would risk coming in contact with a bumper or other structure.
The adapter measures 10.38 inches from the center of the pin hole on the shank to the center of the pin hole on the 2 inch receiver. view full answer...
On front mount trailer hitch, # C31020, from Curt manufacturing, once the hitch is installed on a 2011 Jeep Liberty, there will be 8-7/8 inches of clearance from the bottom of the receiver to the ground. According to Curt, the top of the receiver tube will be directly beneath the bottom most front fascia. There are actually a couple of good pictures in the installation instructions, under step 10, which I have linked for reference. Basically the bottom of the receiver will be about 2-1/2... view full answer...
Since there isn't the exact size you want and the 96 inch length is longer than you'd need your best option would be the longer cable # TC96PB and then coil the harness to take up some of the extra length. You can cut it to length as well. view full answer...
If you have a brush guard and you're not referring to the factory rockguard or skid plate you will most likely need to remove it to flat tow your 2012 Jeep Liberty. All of our base plate kits like the Blue Ox item # BX1131 bolt right to the front bumper below the grill. This an extremely sturdy mounting point which is why most brush guards attach there as well.
The Blue Ox item # BX1131 has been confirmed to fit the 2012 Jeep Liberty with or without the factory rockguard or skid plate.... view full answer...
Since the diameter size of the posts on this u-bolt is 9/16-inch you can ideally use a 9/16-inch or 5/8-inch bit (or even a 1/2-inch bit if you have the room to move the drill around enough to ream the hole to the required size). In either case you will want to ensure that the bits you are using are intended for drilling in the material on your trailer. Please refer to the photo provided which shows the dimensions of this item.
Often it is easier to start a smaller-diameter pilot hole,... view full answer...
The Malone SteelTop Roof Rack - Square Crossbars - Raised, Factory Side Rails - Steel - 58" Long # MPG202 has a total weight capacity of 165 lbs. This is true of the vast majority of roof rack systems. This is the standard roof rack rating but there are some manufacturers that will test the capacity based on the vehicle where other manufacturers like Malone will tell you the rating of their system and you need to check your owner's manual for any further weight restrictions.
For fishing... view full answer...
The best non binding tow bar for the Roadmaster EZ Base Plate Kit item # 521433-1 is going to be the etrailer SD Non-Binding Tow Bar item # e44ZR. This tow bar is compatible with Roadmaster Crossbar-Style Base Plates like the one on your 2012 Jeep Liberty.
The latches on this tow bar let you easily release your Jeep, even at a hard angle or on unlevel ground. It has a stainless steel construction with telescoping arms and a large hookup radius that makes hooking up easy.
I have linked... view full answer...
Think of the 300 pound capacity on front mount receiver # C31020 the same as you would tongue weight capacity on a rear mount hitch. The most vertical weight pushing straight down on the hitch would be 300 pounds. It would still work fine for winching applications even at angles.
Curt front mount hitch # C31020 is currently the only front mount option we carry for the 2009 Jeep Liberty. I have included a link to the installation instructions to the right. view full answer...
Most trailers aren't required to have brakes until they exceed 3500 lb as a rule but state laws can vary as can vehicle manufacturer requirements. However, it is wise to add brakes to a trailer that more than 1/2 the weight of the tow vehicle. Your driving style will have an impact on the safety of towing without brakes.
The bigger issue is your 2012 Jeep Liberty 4x4 is not rated to tow 3200 lbs. Check your owners manual for more information. From what I can find online it looks... view full answer...
The 4-stacked receiver shank # 325-GH-304 as well as the 2-ball mount # 325-GH-031 included with the Gen-Y Adjustable 2-Ball Mount w/ Stacked Receivers - 2" Hitch - 7-1/2" Drop/Rise - 10K, part # 325-GH-314 are constructed of heavy duty steel.
You can most definitely use other brand ball mounts, or any hitch mounted accessory with a 2 inch shank. In regard to the receivers, as you mentioned, three of the four are open, while the fourth has the shank welded to the back of it. Most Class... view full answer...
When laid out flat, the Rola Cargo Net measures 36 by 48 inches. When the extension is added to the basket, it will be 70 inches long, too long for the net to stretch.
The Curt Stretchable Cargo Net, part # C18201 would be a better choice for you. At 38 by 65 inches, the net will provide plenty of stretch to accommodate your cargo.
You might also want to consider a wheel step like part # HE4040 which would make accessing your rooftop cargo much easier, not to mention safer. view full answer...
I went out to the warehouse and pulled the U-Bolt Plate # TRTP300175 to take the measurements personally. I have included a picture showing the correct dimensions for you. view full answer...
I went to the warehouse and pulled this item to get these dimensions. Both the shanks under the basket and that mount to the hitch on the 24x60 etrailer.com Cargo Carrier # e98874 are 2"x2" and are 1/4" thick. Included is a video overview resource for more information. view full answer...
If the Pro Series Hitch Cargo Carrier # PS10401-10402 was mounted in the hitch of a vehicle and you were directly behind the vehicle it would be 48 inches from left to right and 32 inches from front to back.
Check out the picture I attached to see these measurements.
If whatever you have is 23-1/2 inches wide and 42-1/2 inches long you should have no problem transporting it with the # PS10401-10402. You will want to make sure you do not exceed the carrying capacity of this carrier and... view full answer...
Go To Results