For an option without a the reverse lights you would want the Rampage SuperBrite LED Tailgate Light Bar # RA960135, which is other wise exactly the same as the model you referenced.
These bars are 49" long, stand 3/4" tall and have a width of 3/8". view full answer...
When we had the chance to install the Putco Tailgate Light Bar # P92009-60 on a similar Ram as yours we found that we could still access the access hole for the spare. view full answer...
The reverse light circuit is present on the wiring that runs between just the two round connectors of the part # C55384 that you referenced. It's the wire that feeds the center pin. view full answer...
Each little connection wire between the lights on the Alpena Trailblaze Tailgate LED Lights # ALP77229 is approximately 4" in length and the wire with the 4-pole connector is approximately 41-1/2" in length. view full answer...
The Stromberg Carlson 100 Series 5th Wheel Tailgate with Open Design for Dodge Trucks # VGD-10-100 has a measurement from the end to the middle of top bend of 13-1/2 inches. It is about 13 inches from the very start of the bend but 13-1/2 to where it starts to noticeably bend as shown in the attached photo. view full answer...
The wiring harness of the Rampage SuperBrite LED Tailgate Light # RA960135 that you referenced is right at 41 inches in length.
For an extension you would want the part # HM48145 which is 11 feet long. view full answer...
My Erickson representative tells me that when their Big Bed Load Extender is set up as a high mount load bar, The upright will be located 2 feet rearward of the hitch pin hole. So, to determine if you'll be able to open your tailgate, measure 2 feet rearward from your hitch pin hole, and see if that will clear your tailgate. view full answer...
Yes, the Bully Fire Strip LED Light for 48" or 60" Tailgates # BLS-1101 that you referenced comes with two 30 inch strips that can be cut to length if needed.
I attached a review video for you to check out as well. view full answer...
The Boone Outdoor Hardware Tailgate Table # BH70114 referenced in your question weighs only about 22 pounds.
The table top itself measures 20 inches wide and 48 inches long. The table can actually be adjusted to two different height settings. When at its bar height, the table will sit 21 inches above the top of your hitch receiver. When adjusted to the dining height, the table will be 13-1/2 inches above the top of the hitch receiver. The distance from the center of the hitch pin hole... view full answer...
We don't have a 2020 GMC Sierra 3500 handy to test with, so we pulled one of the # CR-007G GMC Brake Lamp Hitch covers from inventory and measured how far the top of the cover extended past the top of the shank that secures the cover in the receiver tube. We found that dimension to be .6 of an inch. Simply measure up this distance from the top inside of the receiver.
If your OEM receiver has a 2-1/2 inch receiver, you'll need a 2-1/2 to 2 inch reducer sleeve, part # C45405 in order for... view full answer...
I was able to go out to the warehouse and measure the Bully Fire Strip LED Light # BLS-1103.
The thickness of the LED and bracket is .179 of an inch or 11/64. The overall height of the LED and bracket is .786 of an inch or 25/32 and the height of just the LED portion is .476 of an inch or 15/32.
The light strip should not be removed from the housing of which it is incased, this will damage the function of the light and void the warranty. If the above measurements do not suit your Escape... view full answer...
I don't think that the dimensions of your tailgate emblem will be listed anywhere but the good news is that if you use a tape measure like part # 8880622 you can confirm as to whether or not the Ram LED Lighted Vehicle Emblem # RP86619 will work as a replacement part.
This emblem measures 5-3/4" wide x 6-1/4" tall. I have attached a photo to demonstrate this as well as a review video where these measurements are taken for you to reference. view full answer...
If you are looking for a longer length than the 12 inches of the Fastaway E2 Shank # FA92-02-4214, the Equal-i-zer Weight Dist Shank - 18" Long - 8" Rise, 4" Drop # EQ90-02-4600 will work with your round bar head weight distribution system. The 18 inch length of the Equal-i-zer is the longest shank length we currently carry. view full answer...
On the Kuat NV 2.0 Base 2-Bike Platform Rack # BA22B the horizontal distance from the hitch pin hole to the center of the nearest bike rail is approximately 14-3/8-inches. The height of the unloaded rack when folded down is 11-7/8-inches relative to the center of the hitch pin hole.
Please refer to the linked Kuat diagram which shows these dimensions. view full answer...
Please see the attached image for the requested measurements of the Lippert Tailgate Storage System Mounting Kit, # LC432336.
The measurements are as follows:
Orange (overall length): 26-1/2 inches
Brown (width of the bend on the back of the bracket): 3 inches
The mounting holes are (red line) 6 inches, (purple line) 3-3/4 inches, (blue line) 2 inches, (green line) 2 inches.
The grey line inner width is 1-3/8 inches and the light brown line out width is 2 inches. view full answer...
The RetraxONE XR Hard Tonneau Cover w/ Trax Rails part # RTT-60311 is 62-3/8" wide at both the cab and tailgate measuring from inside the rails. The rails are both 3" wide so if you wanted the overall width from outside edge to outside edge that would then be 68-3/8" at both the cab and tailgate. This cover will fit the following:
2004 - 2007 Ford F-150 5-1/2 Foot Bed
2008 - 2008 Ford F-150 5-1/2 Foot Bed - with Bed Cargo Management System
2008 - 2008 Ford F-150 5-1/2 Foot Bed - without... view full answer...
It sounds like you have an ATV in your 2014 Ram 1500's bed that requires the tailgate to be down, and you want to use the etrailer Motorcycle Carrier, part # e98873, to carry a motorcycle at the same time. If that's not the case, let me know and I will amend this answer.
The etrailer Motorcycle Carrier doesn't move along the shank per se. Instead, it has three hitch pin hole locations to accommodate different clearance requirements. From the center of the first hitch pin hole to the closest... view full answer...
I went out to the warehouse and took some measurements of the Electric Jack # EJ-3520-BBX that you referenced.
The entire head measures 8-1/4" long (including the buttons) and 4-1/8" wide and 5" high. The motor hangs down about 9-1/2" from the top of the head. Without the buttons the head sticks out 5-1/4" from the front of the mast and 2-3/4" back from the front of the mast.
From the mounting plate to the motor it measures 10" and from the mounting plate to the back of the motor measures... view full answer...
The 2-inch TorkLift Super Hitch that fits your 6-1/2-foot bed 2015 GMC Sierra 2500 diesel is their part # TLC1212 and with it you can use one of their SuperTruss Hitch Extensions like the 28-inch part # TLE1528. This and the 60-inch unit you referenced, part # TLE1560, can be seen on the linked page. Many lengths of extension are offered. You'll want to use the shortest one that will do the job.
Once you have your hitch installed you can measure the clearance you need in order for the... view full answer...