I may have a solution for you, but there is not anything available similar to the Stromberg Carlson # CC-275 that will give you the 150-lbs capacity you're looking for. Instead, you could use a dual hitch adapter like the Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers # D210, and then carry your bikes that way. This may not work if you've got a jack or propane tank on the front of the trailer frame, but it would provide you with a solution otherwise.
It... view full answer...
In order to pick out the correct bearing buddy you will need know the pilot hole of your hub. To do this, remove the wheel and tire and remove the grease cap from the center of the hub. Usually it is a metal cap that is just lightly hammered into place. Use a screwdriver to pry off the cap.
Clean the grease off and measure the opening. I have included a video demonstrating the Bearing Buddy.
The Bearing Buddies # BB1980A-SS for example are for hubs with a 1.98 inch hub bore. view full answer...
Yes, we do have the Amber wobble rollers available. The CE Smith Ribbed Wobble Rollers are 4" Diameter, fit a 3/4" Shaft and are available in Amber Item # CE29536. view full answer...
Yes we have a wide selection of mounting options for your truck camper on your 2005 Dodge Ram Pickup. The Brophy brand has a series of clamps in powder coating, zinc plated and chrome. Such as the Brophy Clamp On Camper Tie-Downs, # HSAB. Or the Brophy Clamp On Camper Tie-Downs - Bed Mount - Zinc Plated Steel, # HSBP.
You may also want to look at the HappiJac Truck-Mounted Camper Tie-Downs, # LC182908-182928. view full answer...
I have attached a link to the covers we carry. I was unable to determine a good recommendation. I will forward a question to manufacturer as well and follow-up with response. Since the Adco RV Air Conditioner Cover for Coleman Mini Mach or Super Mach, # 290-3017 does need meet your needs. view full answer...
The kit you identified is for a Jeep. I suggest the Hopkins Custom Tail Light Wiring Kit for Towed Vehicles, # HM56101 for your 2012 GMC Sierra. Please note the linked installation video. view full answer...
On your 2016 Ford F-150 there is not a different air helper spring kit for if it is a single cab short bed truck or if it has an extended/crew cab, they all share the same kits which is why we do not make mention of the style of bed/cab on our website.
With that said the only thing that affects fitment is if your truck is a 2WD or 4WD.
Out of all of the air helper spring kits for your F-150 I recommend the Firestone Ride-Rite Air Helper Springs - Double Convoluted - Rear Axle # F2582... view full answer...
If I am understanding your issue correctly, you need the Replacement 2" Hitch Adapter for Thule Doubletrack, Hitching Post Pro, # 853-7489. And yes, you slide this on to the shank and screw it into place to hold it. That piece is what upsizes it to a 2". Check out the short 2 min. product review and installation video I have linked as it provides a complete walk through of what to do. You then secure with a hitch pin as usual. view full answer...
For a manual deployed awning, we have available the Solera Universal Awning Support Arms for RVs - Hybrid - 69" Arms - White, # LC434728 and either the Solera 14' White Fade RV Awning Roller and Fabric, # LCV000211475 or the # LCV000223179 for Sand Fade.
Also, checkout the help article I attached titled "HOW TO INSTALL AN RV AWNING FROM SCRATCH".
Happy Camping! view full answer...
We do have the Pace Edwards Bedlocker Retractable Hard Tonneau Cover # PE58QJ which is similar to their JackRabbit Retractable Hard Tonneau Cover # PE59QJ. Both will fit your 2022 Ford F-250 with the 8' long bed. The main difference besides being powered is the Bedlocker uses aluminum slats while the slats on the JackRabbit are covered in Vinyl. This will reduce the chances of the top being damaged on the Bedlocker. view full answer...
The best towing mirrors we offer for your 2010 Honda Ridgelnie are the K-Source universal tow mirrors part # KS69ZR which we know install easily and securely and provide a stable and wide viewing angle behind the vehicle. view full answer...
The Buyers Products 2-1/2" Wide Fender Extension # 337B52150 is only available in a 50' coil so you can either use the other 25' for replacement parts or try to sell it to someone else. I checked with Buyers Products and verified this. view full answer...
You sure can. You'll need the 70 inch JetStream crossbars as part # Y00427 along with the # Y53TR SkyLine towers and the # Y66VR landing pad kit to make the transition between the fixed mounts in your flush rail and the SkyLine towers. You can also add lock cores with part # Y07204.
I've linked to a demonstration video showing a JetStream roof rack being installed on a 2019 Highlander.
It is important to note that a crossbar system should never extend past the mirrors of your vehicle.... view full answer...
We do indeed offer wheel/tire combos that feature a 4.80-12 tire. If you were needing a wheel with a 4-on-4 bolt pattern, I'd recommend part # AM30620 which is a 4.80-12 bias-ply tire on a white spoked wheel with a 4-on-4 bolt pattern.
If you needed a 5 on 4-1/2 inch bolt pattern, use # TA98RR which is a radial tire on a white spoked wheel. Both tires carry an 81 mph speed rating.
I've linked you to our trailer tire help articles which I hope you'll find informative. view full answer...
I do have a way for you to have a 7-way and 4-Pole connector on your 2020 Chevrolet Traverse, but there isn't a wiring harness for your car that comes with both plugs.
You can use the T-One Vehicle Wiring Harness # 118287, which is confirmed to fit your Traverse, and plugs directly into your factory harness. You can then use the Hopkins # HM40975 in place of the 7-way socket that comes with the harness. The # HM40975 also comes with a mounting bracket to easily attach it. view full answer...
We may have a few potential options for your, but I'm afraid we don't carry anything exactly like the fender you referenced. That fender looks very inexpensive, and we do not carry anything quite that cheap. We do have a few basic black plastic fenders that will fit the 12" or 13" wheels. I have listed a few below if you want to take a look.
Fulton Single Axle Trailer Fender - Black Plastic - 8" to 12" Wheels # F008550
Single Axle Trailer Fender w Top Step - Style B - Black Plastic -... view full answer...
I am afraid we do not carry any of the Bobcat wheels in a 5 spoke. Unfortunately we are phasing out the Bobcat wheels. If you are looking for a direct replacement it may be worth getting ahold of Lionshead directly. Otherwise we do have a few similar wheels which I will list below. These are all 16" 8 lug wheels.
Aluminum Liger Trailer Wheel - 16" x 6" Rim - 8 on 6-1/2 - Glossy Black # LH39FR
Aluminum Viking Series Valhalla Trailer Wheel - 16" x 6-1/2" - 8 on 6-1/2 - Black Spoke # AX02665865HDB... view full answer...
We do carry a few racks, such as the Hollywood Racks Sport Rider SE # HLY84FR which are rated for use with heavier bikes weighing up to 80 lbs apiece. This will work great for an E-bike. Unfortunately we do not offer any hitch mounted trike carriers at this time. view full answer...
The Air Lift Air Helper Spring Cradle # AL59DQ is what you're looking for. This will replace the lower roll plate on the # AL57341 allowing for full suspension travel with the air bags. These have a resin construction and drain holes to keep it free from water and debris.
I also highly recommend adding an air compressor like the Air Lift WirelessAIR # AL58WQ. This will allow you to adjust your air bags wherever you go from the cab of the truck. It uses Bluetooth so you don't have to run... view full answer...
The Saris Door County Bike Rack for 2 Electric Bikes # SAR42RR is the only lift bike rack we have but it isn't rated for use on an RV. Instead the next best thing we have is the Swagman E-Spec Bike Rack # S94FR which can be paired with the Ramp and Bridge # S32YR to make it easier to load your heavy bikes onto the rack.
The E-Spec is compatible with any type of RV (towable or a motorhome) as long as you use the included bolt as opposed to the pin and clip. view full answer...