3/4 Shaft Amber Keel Rollers

Question

Question:

Will you please let me know if you have the amber wobble rollers available for 3/4inch shafts?

asked by: Lonnie N

0

Expert Reply:

Yes, we do have the Amber wobble rollers available. The CE Smith Ribbed Wobble Rollers are 4" Diameter, fit a 3/4" Shaft and are available in Amber Item # CE29536.

expert reply by: Jerred H

0

Answer 1

The hub length of the CE Smith Ribbed Wobble Roller for Boat Trailers part #CE29536 is 3/4" per the manufacturer.

view full answer...

Answer 2

I went out to the warehouse and measured Yates wobble roller #YR530R-6P. The width of the center is 1-5/8 inches so it will be too large. Your best option is going to be roller #YR440R which is much narrower but the overall width is 4-1/4 inches. The…

view full answer...

Answer 3

I would be happy to help! The CE Smith Ribbed Wobble Roller for Boat Trailers - PVC - 4" Diameter - 3/4" Shaft - Amber #CE29536 you were looking at has a 3/4" diameter hole that is 5/8" thick. I included a video of the #CE29536…

view full answer...

Answer 4

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 7

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 8

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 9

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 10

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to install…

view full answer...

Answer 11

The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…

view full answer...

Answer 12

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

3/4 Shaft Amber Keel Rollers

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching