The 40k pintle hook part # 33710042 is a fit for the Buyers Products Fabricators Hitch Plate # 3371809043 that you referenced. This is highest capacity option we have with the correct bolt pattern. view full answer...
I recommend one of the Buyers Products Fabricators Hitch Plate Kits for your 2006 GMC Topkick 7500 as there is not a hitch plate specific to your vehicle. Here are the ones we carry.
Buyers Products Fabricators Hitch Plate - 3/4" x 34-1/2" x 22-1/2" # 3371809027A
Buyers Products Fabricators Hitch Plate - 5/8" x 34-1/2" x 22-1/2" # 3371809043
Buyers Products Fabricators Hitch Plate - 1/2" x 34-5/8" x 15-5/8" # 3371809040
Buyers Products Fabricators Hitch Plate - 5/8" x 34-1/2" x 15-1/2"... view full answer...
You will need to have a custom receiver fabricated as the Curt trailer hitch receiver 11748 is no longer in production due to the age and limited numbers of your 2000 BMW Z3. We do have the Weld On Receiver # E17 which will help in the fabrication process for a receiver. You will want to find a local fabrication shop to see if they can help with the fabrication process. view full answer...
It appears you are going to have to have a receiver custom fabricated for your 2008 Mercedes Benz SLK 280. I was unable to find an aftermarket receiver confirmed to fit your SLK. You can use the Receiver Tube # E-912 to aid in the fabrication of a trailer hitch receiver. You will want to visit a local fabrication shop unless you are able to fabricate a receiver yourself and have it welded up. view full answer...
The # 2852 Combo Bar you referenced is meant to be a fabrication part for somebody who's fabricating their own hitch. The outside dimension of the combo bar would actually be a bit larger than 2-1/2 by 2-1/2 inches, so it wouldn't fit in your receiver.
If a 12 inch extension/reducer would work for you, use the # HR26. If you were wanting something longer than that, use the Reese Hitch Box Extension/Reducer, part # RP45292. The extension can be cut down to 24 inches, and is usually used... view full answer...
It appears you will need to have a custom front hitch fabricated for your 2023 Chevrolet Tahoe LS as I do not see anyone manufacturing a custom hitch. The Weld-On Receiver # E17 will aid in the fabrication for a receiver. You will want to visit a nearby fabrication shop in your arear to verify they are able to create a hitch for you. view full answer...
Nobody makes a custom fit front hitch for the 2019 Ford Ranger. If you don't want to install a universal weld-on hitch like the # 41990-07 the other option would be to have a hitch fabricated specifically for your truck. You can take the Curt Weld-On 2" Receiver for Custom Fabricated Hitches # E17 to a local fabricator and have them fashion a front hitch that will allow you to use your snow plow. view full answer...
You may be able to have a trailer hitch receiver custom fabricated for your 2023 Porsche Panamera by a local fabrication shop. Currently there are no aftermarket or factory receivers I can find verified to fit your Panamera. We do have the 2" Weld On Receiver # E17 which will help in the fabrication for a receiver.
I do recommend installing the Curt Powered Tail Light Converter # C59236 after you have a receiver fabricated. This will give you a 4-way flat connector allowing for Auxiliary... view full answer...
Currently we are still awaiting a trailer hitch receiver to be manufactured since the redesign was done on the 2023 Toyota Prius. So while we do not have a receiver for your 2024 Prius we do have a Universal 4-Way Wiring Harness # 119250KIT. This wiring kit uses sensors over the wiring so you will not have to cut into your factory wiring.
For a trailer hitch I recommend contacting a local fabrication shop to see if they will be able to fabricate a receiver for you using the Weld-On Receiver... view full answer...
Curt Combo Bar # C49360 is a fabrication part with a raw metal finish that is intended for use in welding/fabrication. Examples of applications are adding a 2-inch receiver to a suitable vehicle or trailer frame.
But we do offer hitch extensions that are made for use in 2-inch hitches like the one on your 2005 Chevrolet Silverado 2500. These extensions, such as # C45796 from Curt and the others on the linked page, have a powder-coat finish to protect them from corrosion and they do not... view full answer...
As I do not see an aftermarket front mount trailer hitch receiver available for your 2006 Chevrolet Express Van you are most likely going to have to have one custom fabricated. We do have our Weld-On 2" Receiver # E17 which can help with the fabrication process if you are planning on doing this yourself. If this is outside your skill level you can reach out to a local fabrication shop to get an estimate. view full answer...
While I do not see any aftermarket manufacturers with a trailer hitch receiver for your 2020 Volvo S60, you may still be able to have one fabricated at a nearby fabrication shop. The Weld-On Receiver # E17 may help them to create a custom hitch on your Volvo.
I recommend also installing the Curt T-Connector Vehicle Wiring Harness # C56224 when you have the receiver fabricated. This will give you a 4-flat connector which connects to most small trailers. It will also allow for Auxiliary... view full answer...
We do have the Curt Front Trailer Hitch Receiver # 33055 which will fit your 2002 Ford E-350 RV chassis. While there are no custom fit units for your 2012 Subaru Outback you may be able to have one fabricated using the 2" Weld On Receiver # E17. To determine this you will want to visit a local fabrication shop so they can verify if one can be fabricated. view full answer...
Yes, the Solera 16' White Fade RV Awning Roller and Fabric part # LCV000211492 is available without the roller, it's the Solera 16' Replacement Awning Fabric part # LCV000334397. It's easier to replace the roller and fabric together. view full answer...
Currently I do not see anyone manufacturing a custom fit trailer hitch receiver for the 2023 or 2024 Hyundai Ioniq 6. I recommend locating a local fabrication shop near you to have them determine if a receiver can be built. We do have the Weld-On Receiver # E17 which can aid in the fabrication process for creating a receiver. view full answer...
As there are currently no custom fit front hitch receivers for your 2010 Mercedes-Benz Sprinter you will need to have a receiver fabricated using the Curt Weld-On 2" Receiver # E17. You will be able to take this to a custom fabrication shop and have it welded in place along with any additional structure needed on your Sprinter. The oldest Sprinter the EcoHitch Hidden Front Mount Trailer Hitch Receiver # 306-X7352 will fit is a 2016. view full answer...
Currently I do not see anyone manufacturing a custom fit receiver for your 2023 Mercedes-Benz EQE 350 SUV 4-matic. I recommend reaching out to a local fabrication shop to see if they would be able to use our 2" Weld On Receiver # E17 to fabricate a hitch for you. view full answer...
While we do not have a custom fit front receiver for your 2021 Ford Bronco Sport, you can have one fabricated using a Curt Weld-On 2" Receiver # E17. This will allow you to be able to have a receiver welded up at at a fabrication shop near you. view full answer...
I do have a recommendation for you as I do not see anyone manufacturing a custom fit aftermarket receiver for your 2006 Lincoln Navigator. Instead you can have a receiver fabricated and we have the Curt Weld-On 2" Receiver # E17 which will make fabricating a receiver much easier. If you are comfortable working with steel and welding this is something you can tackle otherwise you will want to visit a local fabrication shop to have the work completed.
We do have the 4-Way # HM11140495 which... view full answer...
Thankfully the Dometic, Solera, and Carefree awnings are similar enough that you can interchange replacement fabric between them. So for a 20 foot long Sand Fade color setup you'd want the part # LCV000334438.
I also attached a link to all of the 20 foot long awning fabric replacements we offer as well. view full answer...