Hey Brian, so we have not had a 2024 RAV4 in our shop here quite yet, but I can tell you that the 2023 models that we have worked on have had no such cutout in the rear bumper. From the pictures I can see online of the 2024 model, it also does not appear to have a bumper cutout.
The Curt Trailer Hitch # C13416 installs directly below the bumper, with the crosstube of the hitch completely concealed behind the bumper plastic. The picture below will show you an example of what this will look... view full answer...
No, they will not because the modular bumper is not rated to be flat towed with. Instead you will want the Blue Ox Base Plate Kit item # BLU23XR. This base plate has been confirmed to fit the 2023 Ford Broncos with the Ford Performance Heavy Duty Modular Bumper.
I have linked the installation instructions below so you can see how this base plate gets set up. view full answer...
I checked the install instructions for the Draw Tite hitch part # 76182 and there is trimming of the heat shield but there isn't trimming of the bumper required. view full answer...
Hey Eric,
There isn't a specific torque required for the bumper of your Outback when installing the Curt Hitch # C67JR, so there isn't a number that I can give you. It isn't load/weight bearing so just tighten it down as much as you can and you won't have any issues. view full answer...
Yes, they will! The very first step in the installation instructions, for the Rampage Mass Articulation Front Recovery Bumper for Jeep item # RA88509, goes over how to install your Gladiator's OEM fog lights. I have screenshotted an image from the instructions and attached them below so you can see the process. view full answer...
Yes, you are going to be able to reinstall the removable bumper cover after you install the Draw-Tite Trailer Hitch Receiver # DT42GR on your 2023 Jeep Grand Cherokee. view full answer...
Yes, it does! The crosstube of the etrailer Hitch item # e25TR installs completely behind the rear bumper cover on your 2024 Subaru Outback so you do have to remove it. The crosstube being hidden is one of the best features of the etrailer hitch. Installing it like this leaves only the 2" receiver exposed. This not only looks better it helps with ground clearance.
I have linked an installation video below along with the instructions so you can see how this hitch gets set up.
If you... view full answer...
Yes, it does! The EcoHitch Trailer Hitch item # EH39FR installs entirely behind your 2023 Tesla Model Y's rear bumper. The cover can be reinstalled when you are not using the hitch and be completely concealed.
I have attached a picture along with an installation video so you can see what this hitch looks like once installed.
If you are planning on towing you will also need a wiring harness item # 119250KIT and a ball mount kit item # C45534. view full answer...
I agree and it is available. The Roadmaster Direct-Connect Base Plate Kit # RM35GR is the same as the 521463-5. This is compatible with the bumper and winch on your 2024 Wrangler. They even made sure to show a picture of the bumper with the winch in the attached instructions. view full answer...
Hey Robert, so at this time we do not have an install video for the Curt Hitch part # C63ZV on a 2024 Chevy Blazer EV yet but hopefully we do soon. If you check out the attached install instruction link though you can see that this does not require removing the rear bumper or anything drastic at all. view full answer...
Hey Kevin, the I attached a picture that I took from the install instructions for the Curt hitch part # CU78FR that has the two diagrams. view full answer...
Hello Mark, when installing the Curt # C11473, the curt instructions say to torque the bumper beam bolts to 23 ft lbs. I have linked these instructions for you below. It rare, but not unheard of for Curt to change certain bolt torque specs, so I do encourage you to refer to the instruction manual that came with your hitch to confirm this torque spec. view full answer...
The distance from the center of the hitch pin hole to the edge of the bumper on the # e83ZR is 4-1/2". If that is too far back for your needs I recommend the Curt Trailer Hitch Receiver # C47HR. The same distance on this Curt hitch is only 2". I also like this hitch because it has a concealed cross tube. This gives it a nice clean look since you don't have the cross tube hanging down at the rear of your vehicle. Both of these will work with the # C45534 you were looking at. If you need... view full answer...
The Bumper Brackets # C19748 for the Curt Adjustable Tow Bar # C19745 are supposed to mount ridged to the towed vehicle. The arms themselves connect to these with the pins which allow the arms to pivot for changes in road elevation and when turning. view full answer...
Hey Pep!
According to the photos in the installation instructions for the Curt Trailer Hitch Receiver # C29VV it looks like the receiver sticks out just a little from the bumper.
The center off the hitch pin hole is 2-1/2" back from the front face of the receiver (see attached). view full answer...
Yes, the Roadmaster Single Park Light Diode # RM-690 can absolutely be used for this purpose. The main function of the diode is to stop feedback so having these installed inline will prevent any unwanted interaction between the aux light and the rest of the vehicles wiring systems. view full answer...
Curt doesn't make hitches with detachable receivers. The only one they offer that fits your 2018 GLE 350 that does not require trimming is their item # C13294 you were looking at.
The Curt Hitch item # C13294 is custom fit and bolts to your Mercedes with included hardware. It is a class III hitch with a 2" receiver. It has a 7,500 lbs towing capacity and a 750 lbs maximum tongue weight.
I really like the Curt item # C13294 because it installs behind your rear bumper cover leaving only... view full answer...
Yes, you will but it is a portion of the bumper/fascia that will only be seen if you're under your Jetta. I have attached a screenshot below of the section of the instructions for the Draw-Tite item # 24978 that shows exactly where to make the cuts and how large they are.
I have also linked the instructions below along with an installation video so you can see how to get this hitch set up on your 2024 Volkswagen Jetta GLI with dual exhaust. view full answer...
Nope, you do not have to do any bumper fascia trimming on your 1997 Chevy Suburban to install the Curt Front Mount Hitch # 31042.
You don't have to do any drilling, either so it's just a bolt-on installation. As for clearance, from the top of the brackets to the bottom of the tube it is 4 inches. view full answer...
You are correct that the Jeep bracket should have been reinstalled when installing the Blue Ox Base Plate # BX1139. I have linked another video near the bottom of the page where you can see the brackets being reinstalled on a 2020 Jeep Wrangler around the 12:50 mark of the video. This can also be seen on page 9 of the installation instructions which are also linked near the bottom of the page. view full answer...