The # 8-247-50UC3-EZ and # AKHD-545-35-G-EZ-K will both fit and work with your 13" wheels. These are also compatible with the # 40716-15 from your previous question. For the most part it comes down to cost between the two hub/drum assemblies. However, since this will be going in the water on your boat trailer I would stick with the Dexter which has the 500-hour salt spray rating.
The Hydraulic Brake Kit # AKFBBRK-35-D will work with your 13" wheels but I would stick with the Demco. The... view full answer...
Hey Bob,
Yes the etrailer Boat Trailer Jack w/ 2 Wheels # MJ-1500B-DWL will most certainly fit your 2" x 2" trailer frame without wobbling around. It fits frames up to 2" tall and you can tighten the clamps to the point you're going to get a nice, snug fit. view full answer...
Hi Angel,
It'll be perfectly fine going from a 14" x 6" wheel to the 14" x 5-1/2" Dexstar Steel Directional Trailer Wheel # AM20377.
Trailer tires that fit 14" x 6" wheels will also fit a 14" x 5-1/2" wheel so you won't have any issues. view full answer...
For a trailer with a 4.80-12 tire size you would need either a 4-Lug # AM20124 or 5-Lug # AM20134 wheel. We do have these with tires already installed as the 4-Lug Package # AM30630 or 5-Lug Package # AM30670 so you can just bolt them on and go. view full answer...
Hi Rodger; you can absolutely replace your 63-3/4 inch boat trailer fenders with the 65 inch Tandem Axle Teardrop Trailer Fenders for Boat Trailers # HP34VR.
We're talking just a hair over 1/2 inch longer on either side so it won't be an issue. Finding a 100% exact match for fenders is very, very difficult so there is some wiggle room and the # HP34VR will work out for you. view full answer...
Hello John. After looking thru all of the snap-ring jacks we carry, I am sorry to say that we do not offer anything with a wheel that will also use a 1/2" pin. We do have a jack with a wheel and a snap ring that uses a 3/8" pin, the Fulton # FTJ120W0301. We also have one snap ring jack that does use a 1/2" pin, part # TJB-2001-Z, but as lock would have it, this jack has a welded foot plate instead of a wheel.
I know neither of these options fit your description exactly, but these will... view full answer...
Thanks for the information! Our spare tire carriers are pretty universal and the best one for your boat trailer is going to be the CE Smith Offset Spare Trailer Tire Carrier item # CE27310G. It is made of galvanized steel so it will stand up well to being in and out of the water. It fits all 4-lug and 5-lug wheels, up to 15" to include 4 on 4, 5 on 4-1/2, and 5 on 4-3/4 bolt patterns. It'll mount to trailer frames that are 1" to 3-1/2" wide x up to 4" tall. view full answer...
Hey Frank, the Westlake ST205/75R15 Radial Tire w 15" Condor Aluminum Wheel # WST74FR is not pre-balanced and it doesn't require it. Trailer wheels do not end up getting balanced and when people try to it doesn't really offer any benefits. view full answer...
That's totally fine, Rob. Since the tire you're wanting to use is smaller in diameter you'd have no issues fitting it into your existing wheel well. view full answer...
The Fulton Single Axle Trailer Fender # F008594-2 does have a 4-1/8" wide mounting bracket slot, so they will fit nicely with the 4" wide brackets on your McClaine trailer. The mounting holes on the fender are 3-3/4" apart though, so you would have to put a new hole in the current fender bracket, but as long as you are comfortable doing that it will work nicely. The Fulton Single Axle Trailer Fender # F008594-2 is 42-5/8" long overall and 12-3/4" tall so we would want to make sure that... view full answer...
The # AM31994 has a 24.1" outer diameter. Your typical 4.80-8 tire found on the # CE48810 has an outer diameter of 16.1" which means you're going to lose 4" of clearance on top of the tire. The only way to use this would be to remove the fender. view full answer...
Hey David, all of the pontoon boat guide ones we offer are designed to fit on the inside of the pontoons like with the part # CE27672. Is there a reason you want them on the outside? view full answer...
Thanks for reaching out again, Mike!
Yes, the Tekonsha Prodigy P3 Trailer Brake Controller # 90195 is compatible with a hydraulic boat trailer system. It's arguably the most reliable option on the market when it comes to compatibility with electric over hydraulic brake systems so I know you'll be happy with how it performs!
You just need to make sure you have an electric over hydraulic actuator like the Hydrastar Vented Marine Electric Over Hydraulic Actuator for Drum Brakes # HS381-8065... view full answer...
It is acceptable and highly water insoluble so it is great for boat trailers. Grease like the LubriMatic LMX Industrial Strength Grease # L11390 is a lithium complex. The same is true for Lucas Red N Tacky which means they are compatible. view full answer...
Yes Dylan, the Curt Trailer Hitch Receiver # C11030 can be used on the C300. This hitch has a 2,000 lb weight capacity, so as long as the small boat trailer you have isn't over that you're good to go.
As far as wiring goes, we don't have anything custom but we do have the Hopkins Wiring Harness with 4-Pole Flat Trailer Connector # HM38168 which is universal harness. view full answer...
We do have a potential solution for you. Unfortunately, the swing away actuators like the one on your 2005 Mastercraft trailer have been discontinued, so I am afraid there is no direct replacement, or anything that will fit inside the current swing away.
At this point we would have to recommend replacing the tongue of the trailer entirely, all the way down to the swing away. For a replacement option I recommend the Dexter DX7.5L A-60 Brake Actuator w Electric Lockout # DX89FR. This has... view full answer...
Hey Glen,
I'm going to need some dimensions and pictures of the current fenders in order to find a direct replacement. If you want to email me this info I'd be happy to look for a compatible fit. view full answer...
There's only one option that will fit your 2008 Ram truck with a welded on hitch that will work with the SuperTruss hitch extensions. It is the TorkLift SuperHitch Magnum Trailer Hitch item # TLD1102-30 so I highly recommend it.
This 2-1/2" hitch combined with your factory 2" hitch will allow you to use a SuperTruss Hitch Extension like item # TLE1536.
There are also many options available for camper tie-downs that I have linked below. view full answer...
Hi Pete; thanks for the question and to answer it, there are indeed balancing beads that will fit your 4.80-12 trailer tires. What you need is the following:
- Counteract Tire Balancing Beads # CA68VR
The # CA68VR is designed for 8" to 12" tires and is enough for four tires. view full answer...
Hello Erik, it certainly is possible to convert your trailer from surge brakes over to electric-over-hydraulic (EOH) brakes. Basically, all you will need to add is an EOH disc brake actuator # HBA16 and a wiring kit # HS381-9000. The wiring kit contains everything you need to install and wire in the actuator, including a junction box for your connections. You will simply attach the brake line from your surge coupler to the Hydrastar actuator.
As long as the current surge actuator is still... view full answer...