Expert Answers about Chevrolet Uplander
- Brake Controller and 7-Way Trailer Connector Recommendation for a 2006 Chevy Uplander
- You would need to convert the 4-way to a 7-way so that you can install the brake controller. For that you will want the Brake Controller Install Kit and 7-Way Adapter part # ETBC7. I attached installation instructions and an install video for this product as well.
For a brake controller I would recommend the Prodigy P2 Brake Controller part # 90885. This is our best selling brake controller because of how well it works and how easy it is to setup.
view full answer... - Trailer Hitch, Ball Mount, Hitch Ball, and Trailer Wiring for a 2009 Chevy Uplander
- I spoke with my contact at Curt and she stated that, technically, Chevy stopped making an Uplander for the US market in 2008 so there is no 2009 model. They did continue to make them for the Canadian market which is why the Tech Tip states the hitch is for that market.
However, she stated that as long as your 2009 Uplander has the 121 inch wheelbase, the Curt Hitch, # 13336 will fit. If yours does not have a 121 inch wheelbase, or you are not certain, she stated you could use Curt Hitch...
view full answer... - Recommended Trailer Hitch and Wiring for 2008 Chevy Uplander
- For your 2008 Chevy Uplander, I recommend the Draw-Tite Class III Max Frame Receiver Hitch # 75278. This Class III hitch is confirmed to fit your vehicle and has more than enough capacity to pull your 1,000 pound trailer with inflatables. It will provide you with a 2 inch receiver that will work great with a ball mount for towing or other accessories such as a bike rack that you may want to use down the line.
I have attached an installation video on your Uplander that you can use for...
view full answer... - How to Pick Out a Weight Distribution System for an A-Frame Trailer
- You have a pretty standard A-frame trailer frame that would work well with weight distribution hangers and brackets. You may have to temporarily remove the battery box to install the frame hangers.
The best way to pick out a weight distribution system is to base it off of the loaded tongue weight of the setup when it is loaded and ready to tow. This figure also includes the weight of any cargo behind the rear axle of the tow vehicle. I attached a help article on determining tongue weight...
view full answer... - Use One Ballmount to Tow Multiple Trailers - a 1-7/8 Inch and a 2 Inch Diameter Trailer Ball
- I would like to clarify some terminology so that we are on the same page, the hitch is the part attached to your 2008 Chevy Uplander. Then the ball mount or drawbar is attached to the hitch receiver using a pin and clip, or locking mechanism. Then the ball mount is outfitted with the appropriate size trailer ball. The diameter of the trailer ball shank needs to be compatible with hole the ball mount and the diameter of the trailer ball needs to be compatible with the trailer coupler.
Since...
view full answer... - Recommendation for Complete Towing Setup on a 2007 Chevrolet Uplander 3.9 Liter
- I did some research on your 2007 Chevrolet Uplander and found that the maximum recommended towing capacity for this vehicle is 3,500 pounds. If your trailer is 2,600 pounds empty, you would be limited to 900 pounds or less of cargo. If 900 pounds of cargo sounds about right, you will need to check your hitch capacities and make sure it is capable of towing 3,500 pounds. You may find that a weight distribution system is needed to safely tow the maximum capacity with your vehicle.
You should...
view full answer... - Which Transmission Line is the Return Line for on a 2007 Uplander for Install of Cooler
- When you install a supplemental transmission cooler in a vehicle you want it to be downstream of the factory cooler in the radiator. When we installed a cooler in similar Uplander as yours we found that the return line (the one to use for installation), was the one nearest the radiator cap.
To verify which line to use you can go out to your vehicle when it is cold and start it up, put it in gear and while holding the brakes raise the rpms by pressing the accelerator slightly. Quickly turn...
view full answer... - How Does Hitch Install on Chevy Uplander with Load Leveling Compressor
- On your Chevy Uplander, the Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2" # 75278 will fit with your load leveling compressor. It will take some extra time to make sure that you have the proper fit, but the bracket will reinstall over the hitch receiver mounts. Basically you just remove the one bolt that holds the compressor on and then install the hitch flange behind the bracket and the bolt through it.
view full answer... - Rhino-Rack Roof Rack for 2009 Chevy Uplander
- If your 2009 Chevy Uplander is equipped with factory raised rails that run front to back on the roof then we do have the Rhino-Rack Vortex Roof Rack System that consists of # RRVA118B-2 for the two 46 inch Vortex Aero Crossbars in Black or # RRVA118S-2 for Silver and # RRSX100 for the SX Series Legs.
This is a sleek, aerodynamic system that will provide you with a quiet ride and a weight capacity of 165 pounds. I have attached a video review that you can check out as well.
If your Uplander...
view full answer... - Is Install of Rampage Minivan Center Console # RA39923 Reversible
- The removable tray seen in the customer submitted pictures of the Rampage center console part # RA39923 does not come with this. In the pictures you can see that the tray is too big to fit in the console as well so it wouldn't be a great fit. It is a really great and well made console that you could reverse if you really wanted to.
view full answer... - Transmission Cooler Recommendation for a 2008 Chevy Uplander
- Transmission coolers are not vehicle specific so you can use any one that will fit in the space you have available in the engine compartment. There are 3 locations you could mount the cooler: in front the A/C condenser, behind the condenser and in front of the radiator, or behind the radiator which is not very efficient.
Check these areas for how much space you have to make sure a cooler fits. The most popular cooler is # D13503. It measures 11 inches across, 8-3/4 inches tall, and 7/8...
view full answer... - Wiring Harness Recommendation for a 2008 Chevrolet Uplander
- Both the Tekonsha T-One # 118396 and the Curt T-Connector # 56077 wiring harnesses will work for your 2008 Chevrolet Uplander like you mentioned, and out of both options I recommend the Curt simply because it's much easier to install but still produces the same result.
The Curt plugs into a factory connector while the Tekonsha tees in behind the tail lights. So both options fit your vehicle, but the Curt is just easier to install since you only need to access that one side of the vehicle.
Both...
view full answer... - Parts Needed to Flat Tow a 2007 Chevy Uplander
- We do offer parts to allow your 2007 Chevy Uplander to be flat towed behind a motorhome. You would need to first start with a base plate kit. For that you would want the # BX1663.
In addition to the base plates, you will also need a compatible tow bar, safety cables, lighting, and supplemental braking to flat tow your vehicle. The most popular compatible tow bar is the Blue Ox Avail # BX7420. The great thing about this model is that it comes with safety cables.
For lighting you can use...
view full answer... - Roof Rack Recommendation for 2006 Chevy Uplander
- Thule does not make a roof rack solution that fits the naked roof versions of the 2006 Chevy Uplander. Closest thing would be the Inno brand roof rack that consists of part numbers # INB127, # INSUT, and # INK585. This won't reuse any of your Thule roof rack but your roof carriers will fit this same square bar style of rack that you had.
view full answer... - Trailer Hitch and Wiring Recommendation for a 2006 Chevy Uplander
- Whenever available I always recommend a Class III 2 inch hitch for vehicles as they have higher towing capacities and since more accessories are made for 2 inch hitches they offer greater flexibility as well. For that you would want the Draw Tite hitch part # 75278. I attached an install video for you to check out as well.
Since you wanted to do some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop...
view full answer... - Recommended Roof Rack and Cargo Basket for a 2008 Chevy Uplander
- If you have factory rails that run front to back, I recommend the Evo Raised Rail Feet # TH710401 and 53" WingBar Evo Crossbars # TH711420. This Thule load bar will work with the Curt roof mounted cargo basket # C18115 you referenced because it is less than 3-inches in width. The Curt cargo basket # C18115 requires crossbar spacing of 15, 22 or 29-inches
On the other hand, if your 2008 Chevy Uplander doesn't have existing rails or crossbars, we currently don't offer any roof racks.
Anytime...
view full answer... - Parts Needed to Tow Trailer with 2008 Chevy Uplander
- Congratulations on the addition to the family!
I took a look at the online version of the owner's manual for your 2008 Chevy Uplander and it lists a maximum trailer weight of 3,500 pounds. With this in mind your van is more than up to the task of pulling your loaded boat trailer with a healthy safety margin intact. Since you will be staying well under the vehicle's limits towing the trailer shouldn't put too much stress on the transmission or engine. I do just recommend verifying this...
view full answer... - Trailer Hitch and Wiring Recommendation for 2009 Chevy Uplander
- For your 2009 Chevy Uplander we have the Draw Tite Hitch part # 75278 as a confirmed fit that would work well. It installs easily, is mostly hidden, and has great towing capacities. Then for trailer wiring the Tekonsha kit part # 118396 would be a really great option that installs easily as well.
Pour votre Chevy Uplander 2009, nous avons la pièce d'attelage Draw Tite # 75278 comme un ajustement confirmé qui fonctionnerait bien. Il s'installe facilement, est principalement caché et possède...
view full answer... - Trailer Hitch that Fits 2008 Chevy Uplander with 109 inch Wheelbase
- Yes, for your 2008 Chevy Uplander with a 109 inch wheelbase part # 13344 is a confirmed fit. I attached an install video for you to check out for more info as well.
For trailer wiring you then would want the part # 118396.
If you wanted to do some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin...
view full answer... - Transmission Cooler Recommendation For 2008 Chevrolet Uplander
- Since transmission coolers are not vehicle specific, we recommend getting the biggest cooler that will fit in the available space.
The transmission cooler you referenced in your question may work well for you 2008 Chevrolet Uplander. The Derale Series 8000 Plate-Fin Transmission Cooler Kit, part # D13502 measures 11 inches wide x 7-1/4 inches tall x 7/8inch deep. This cooler is designed for vehicles with electronic overdrive transmissions and will help prolong the life of your transmission....
view full answer...
Go To Results