Expert Answers about Infiniti M37
- Trailer Hitch Compatible with 2012 Infinity M37
- The 2012 Infinity M37 is the rear wheel drive versus the M37X which is all wheel drive. This will not change the hitch fit at all, so the Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4" # C11111 will absolutely fit your M37.
It is an installation you can do yourself, but it does require removing the bumper and trimming an underbody panel. There is no drilling required and I've attached the installation details to assist.
If you will be using this hitch for a bike rack...
view full answer... - Appearance of Curt Trailer Hitch, Part # C11111, After Installation on the 2011 Infiniti M37 Sport
- I do not have a photo of a completed installation performed by etrailer with this particular hitch , Curt Trailer Hitch for the 2011 Infiniti M37, Part # C11111, on your specific vehicle. However. within the manufacturer installation instructions there is a representative photo showing this product installed. I have included a close-up image of this photo.
It is worth noting that this hitch installation on your vehicle is fairly involved and the manufacturer rates the level of difficulty...
view full answer... - 2012 Infiniti M37 Trailer Wiring Recommendation
- Installing trailer wiring in your 2012 Infiniti M37 would not take 8 hours to complete. The ZCI kit part # 119250KIT is the correct kit to use and the one I recommend. It uses sensors to attach to the taillight circuits of your vehicle and does require running a power wire up to the positive post of your vehicle battery. Your vehicle has separate turn signals from the stop/turn circuits which makes the install of this not overly difficult at all.
view full answer... - Trailer Hitch for a 2011 Infiniti M37x
- The only trailer hitch for the 2011 Infiniti M37x is # C11111 and it is a Class I hitch with a 1-1/4 inch receiver. You could use an adapter, # HTAD, to use the hitch with 2 inch accessories. However the use of an adapter reduces the tongue weight of the hitch by 50 percent from 200 to 100 pounds.
Since you want to use the hitch for accessories such as a bike rack and cargo carrier, and if looking at new ones, you have to make sure the accessories are rated for use with a Class I trailer...
view full answer... - Is there Substantial Modification Required to Install a Hitch on a 2012 Infiniti m37x
- The Curt Hitch # C11111 will not require drilling for installation on your 2012 Infiniti M37, however there will be some trimming of the underbody panel prior to installation. This trimming would not be visible from the rear of your vehicle. This trimming is necessary to allow the receiver opening to pass through this panel. Check out the installation instructions that I attached that show how it will be modified.
This hitch comes with a ball mount and a pin and clip. You may also be interested...
view full answer... - Inside Width of Front Hanger for Dexter 10,000-lb General Duty Axles
- The Front Hanger for Dexter 10,000-lb General Duty Axles # 10GDH-FTRH34 that you referenced has an inner width of 2-1/2 inches which is the spring width it is designed to fit. This is a higher capacity type of spring used on 10,000 lb rated Dexter axles.
view full answer... - 2011 Infiniti M37 Trailer Wiring Harness Recommendation
- For your 2011 Infiniti M37 we do have trailer wiring available, but they are all universal fit harnesses that will require you to test the wires of your taillight harnesses and splice into them accordingly.
The ZCI kit part # 119250KIT is one of the confirmed fits and requires no splicing to the taillight wiring. It instead uses sensors that clamp to the wiring. This would be the best solution.
view full answer... - Correct Trailer Hitch Fit for a 2012 Infiniti M37
- I checked with Curt and confirmed the Curt Trailer Hitch Receiver part # C11111 is a fit for a 2012 Infiniti M37 all models. It will work great for bike racks just make sure the rack is for a 1-1/4" receiver and you abide by the 200 lb weight capacity.
view full answer... - Can a 2012 Infinity M37 Sedan be Flat Towed Behind a Motor Home
- I checked the owners manual for the 2012 Infinity M37 and it states that it will have to be towed using a tow dolly such as # RM-2050-1. The vehicle cannot be flat towed with all the wheels on the ground because it can damage the transmission.
This tow dolly comes with lights and electric brakes. To activate the brakes you will need to have a brake controller installed in the motor home. For a brake controller I recommend the P2, # 90885. But you may need some additional wiring to install...
view full answer...
Go To Results