I do have a great option for you but we do not have a standard front sway bar available for your Freightliner M2 chassis with the 10,000 pound front axle.
What you can use at the front that will still really help with keeping the RV in line and minimizing wander is the Roadmaster TruTrac # RM-TRAC-FM2. This Trac Rod essentially braces the axle to prevent jarring and will control any of that excessive side play during travel. It will install using existing holes in the chassis' frame so... view full answer...
Based on the information I could find on your 2011 Freightliner M2 cab and chassis it appears you have a 34" wide frame. The Buyers Products Flatbed/Flatbed Dump Hitch Plate Bumper # 3371809050 is specifically designed to fit a 34" wide frame. It has bolt hole which you can use to attach to your frame but welding is also required. You are able to bolt on either a 2" Receiver # 3371804055 or Pintle Hitch w/ 2-5/16" Ball # BP38FR.
For tail lights I recommend the LED Combination Tail Lights... view full answer...
If you plan to leave you chassis exposed and not put a bed on your 2011 Freightliner M2 cab and chassis the Buyers Products 42" x 13-1/2" Gooseneck Hitch Plate # 3373014981 is going to be your best option. This is recommended to be welded to your frame rails.
If you plan on adding a type of bed/flatbed the B&W Turnoverball Underbed Gooseneck Trailer Hitch # BWGNRK1500 is going to be your best option. This will allow you to remove the hitch ball when you need to use your bed and replace... view full answer...
It's not likely your International has a factory connector for an electric brake controller adapter. But you can still install a Prodigy P3 # 90195 by hardwiring it into the RV.
You will wire the P3 in by connecting the black wire to the positive side of the RV's battery, the white will need to be grounded which can be done to the negative side of the battery, the blue goes to the trailer connector at the back of the RV and red goes to the cold side of the stop light switch. The stop... view full answer...
The grease seal 010-036-00 that you mentioned is our part number # RG06-070 but then for the exact matching oil bath seal with same dimensions you'd want the part # 10-63. view full answer...
For your Dynaquest 360XL motorhome, I recommend using the Ultra-Fab Skid Wheels for Class A RVs, Item # UF48-979013. These sturdy steel wheels have a 6 inch diameter and attach to the rear of your RV to help prevent the tail from dragging. These skid wheels are intended for motorhomes longer than 34-feet.
I have attached a video for you to check out. view full answer...
The Trailer Valet RVR9 Remote-Controlled Trailer Dolly # TVRVR9 that you referenced will work great if you can keep the trailer weight under 9,000 lbs as that is it's weight capacity. The number of axles would not be an issue at all. view full answer...
While we do not have a custom fit hitch for your Freightliner MT45 we do have several heavy duty weld-on hitches that could work for you. I have included a link to all of them for you.
Based on your frame width you could use # 41990 which is 44 inches long. Then for brackets you could use 7 inch brackets # 4907 or 16 inch brackets # 4916.
If the frame is an I-beam frame then the only option is # 13703.
Weld-on hitches should only be installed by qualified professional welders. I have... view full answer...
Glad to hear that you've enjoyed your past experience with the SumoSprings on your last motorhome. The Timbrens are constantly compared to/against the SumoSprings so since you liked the SumoSprings you'll enjoy the ride quality here as well.
The Timbren Suspension System # TFRM2L is for if you have a leaf spring suspension, but from what I could tell in my research I believe your 2019 Renegade Verona LX has an air spring suspension so you'll want the Timbren part # TFRM2A instead. Aside... view full answer...
For a motor home built on a Freightliner M2 chassis we have both front and rear anti-sway bars that will fit various versions. The linked page will let you select your vehicle version from the drop-down menu at the top of the page to then see suitable anti-sway products. One of these will be your best bet if you're flat towing your Edge and want to improve handling. If you are not sure which chassis you have you can check with Fleetwood by providing your motorhome's VIN number.
If you... view full answer...
There are no specific fits for a 2013 Freightliner M2 for a hitch or wiring, so your best option is a weld-on hitch. If your frame is up to 44 inches you can use the Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver # 41990-16 for 16 inch tall brackets or Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver # 41990-07 for 7 inch tall brackets.
Then for a 7-way you will need to hardwire in the Vehicle Wiring Harness # C59236 with the Universal Installation Kit for Trailer... view full answer...
Prior to a breakaway event the breakaway cylinder for Roadmaster BrakeMaster System # RM-9160 will be charged from the connection to the air brakes from the RV. The passage below explains what happens should a breakaway event occur:
In the unlikely event that your vehicle separates from your motor home, the included breakaway system will give you peace of mind. Just mount the breakaway switch at the front of your towed car and wire it to both your battery and to the BrakeAway air reservoir.... view full answer...
To install a trailer brake controller and 7-way connector on your 2007 Freightliner M2 you'll need the Universal Installation Kit for Trailer Brake Controller # ETBC7 along with additional 10AWG # 10-1-1 wire to run the length of your vehicle.
Since you won't have a 4-way wiring harness you'll need to first install the Hopkins Endurance 4-Way Flat Trailer Connector # HM48110. This can be spliced into your tail lights for a quick and easy installation that will make wiring in the # ETBC7... view full answer...
The Global Link RV Baggage Door Slam Latch part # 295-000015 is a direct replacement for select Global Link, Fastec (FIC), Bauer, and Lippert Components locks. It looks like you have a Fastec (FIC) latch which came with both a normal plunger and extender plunger. If you have a normal plunger then the Global Link RV Baggage Door Slam Latch will work just fine as a replacement but if you have the extended plunger we do not have a replacement for this unfortunately. I have attached a photo... view full answer...
In order to choose the correct SnapPads for your motorhome you must measure and note their shape. If you know the brand of leveling system that would certainly help as well. Unfortunately, we cannot state exactly what SnapPads fit any one particular trailer as there are no records of this outside of maybe the manufacturer and even then it could be unclear. The SnapPad EQ Plus Jack Pads for Equalizer Leveling System part # SP64FR84 for example fits Equalizer Leveling Systems with 10" round... view full answer...
For your Ram 3500 A-frame trailer jack the cover you'd want is the part # UF38-944020 which is waterproof and the correct size for the jack that you have. view full answer...
The Andersen Ultimate Connection 5th Wheel Trailer Hitch System with Adapter # AM3200 is 24 inches long by 24 inches wide and will sit 12.5 inches above the bed rails. When you add the hitch ball, it will be 15.75 inches, 16.875 inches, or 18 inches from the base to the top of the hitch ball. I've attached a photo of the manufacturer's dimensions to assist. view full answer...
Is your controller in hydraulic mode? Sounds like it may not be based on what you described. The P3 part # 90195 is compatible as-is with electric over hydraulic brake actuators like the Hydrastart # HBA16 but it has to be put in "hydraulic mode" view full answer...
The length of the PTC Custom Fit Cabin Air Filter # 3513033 is 13.5 inches, the width is 6.6 inches, and the height is 1.18 inches.
This fits the following vehicles:
2000 - 2003 Ford Escort
2000 - 2009 Ford Focus
2010 - 2013 Ford Transit Connect view full answer...
I checked with my contact over at Roadmaster and he tells me that you'll want to check the U bolt pattern on your suspension in order to make sure you get the correct sway bar, since there could be two potential fits for your 2015 Freightliner M2 Sport Chassis. If you've got a 5"x4" bolt pattern, then the # RM-1209-106 will work for you. If you've got the 6"x4" bolt pattern then you'll want to use the # RM-1209-113.
This would be the only way to determine the correct fitment for this chassis. view full answer...
Go To Results