Expert Answers about Subaru Legacy

• Installing Curt Trailer Hitch on 1999 Subaru Legacy
• Yes, even if the tow hooks on your 1999 Subaru Legacy do not look the same as the ones in the install video you will still install Curt hitch # C12270 in the same way. No matter what your tow hooks look like, according to the directions when raising the hitch into position the driver side plate will be to the outside of the tow loop and the passenger side plate will be to the inside of the tow loop. Please note that with this hitch, all non-trailer loads such as bike racks and cargo carriers...
  view full answer...


• Tire Chains for 1990 Subaru Legacy
• For a 2WD vehicle, chains should be placed on the drive wheels. On a 4WD vehicle, chains are typically placed on the rear wheels, although all four wheels may be chained unless your owners manual prohibits it. To view the selection of snow chains, use the provided link and follow the drop down menu for your tire size. I have also provided a link to our snow chain FAQ page which covers many frequently asked questions about snow chains.
  view full answer...


• Can DIYer Install EcoHitch Trailer Hitch on 2020 Subaru Legacy
• A do-it-yourselfer can 100 percent install the EcoHitch trailer hitch receiver that fits your 2020 Subaru Legacy, which is the following part number: - EcoHitch Hidden Trailer Hitch Receiver # EH36RR Installing the # EH36RR does require you to remove the bumper beam on your Legacy and install the hitch crosstube in its place, but does not require any special tools, just standard tools needed for any hitch install such as a screwdriver, ratchet, and torque wrench. So if you're even somewhat...
  view full answer...


• Do Access Holes Have to be Drilled to Install a Trailer Hitch on a 2010 Subaru Legacy
• The top of the frame rails on the 2010 Subaru Legacy are covered and you cannot get them in from above. An access hole must be drilled on both sides like in the video I have linked. i have also linked the instructions for you. If you plan on doing some towing I recommend the etrailer ball mount kit # 989900. It comes with 2 ball mounts, 2 balls, a hitch pin with clip, and a carrying bag. For trailer wiring, use # 118511.
  view full answer...


• Trouble Lining Up Bolt Holes to Install Draw-Tite Hitch on 2006 Subaru Legacy
• Sounds like you either have the Draw-Tite Class II # 36334 or Class III # 75560 hitch receiver for your 2006 Subaru Legacy. While this is a custom fit hitch that should bolt right up no problem, the mounting brackets may have become bent during shipping which is why you're having issues getting the bolt holes to line up (if you're talking about something else please let me know). This is common enough that we actually have a helpful article on how to handle this type of situation which...
  view full answer...


• Replacement Hitch Install Hardware for a Curt Hitch on a 1995 Subaru Legacy
• It sounds like there may have been a hitch installed in your 1995 Subaru Legacy at one point since you said there already is a 1/2 inch hole in the frame. As long as the brass plug you found is just a plug then you would want to have it removed so that you can install the hitch. To get all new hardware for the part # C12270 which has been confirmed to fit your 1995 Subaru Legacy you will need the part # RHK. On its product page you will need to enter the part number and we will ship you...
  view full answer...


• Are the Rubber Strips of the Rhino Vortex rack RR37XR Designed to be Cut
• The rubber strips that come with the Rhino-Rack Roof Rack # RR37XR are designed to be cut as that allows you to install a channel mounted roof rack accessory on the rack and then use the appropriate length of rubber strip to fill the channel back in to reduce wind noise. Most likely they just gave you sections that were too long as they have different length bars and likely just use the same filler strips for all of them.
  view full answer...


• Does T-Connector Wiring Harness # 56091 Connect to the Battery on a 2011 Subaru Legacy
• The Curt Circuit Protected T-Connector Vehicle Wiring Harness, # 56091, does not require a power wire to the vehicle battery. It is a T-connector that plugs in line with the vehicle tail lights. Only the ground wire needs to be manually attached to a bare metal surface. I have included a link to the installation details for you to view.
  view full answer...


• Installing a Trailer Hitch on a 1993 Subaru Legacy
• You will at the very least need a 1/2 inch wrench and a torque wrench that is good for 110 foot pounds. It is important to get the bolts to the proper torque rating. If they are too loose you could lose the hitch. Too tight and you could damage the hitch or your 1993 Subaru Legacy. Most auto parts stores can loan out any tools you might need. You should not have to have the car on a lift to install it. lying on the ground would likely be fine. Some people who want more space would jack...
  view full answer...


• Where is Stoplight Circuit Switch on 2011 Subaru Legacy for Brake Controller Install
• Use a circuit tester like the part # PTW2993 to test the wires that run to the brake light switch you have found till you find one that has voltage only when the brake pedal is pushed. This is the correct circuit to tap into for the red wire of your brake controller install.
  view full answer...


• Do Class II and III Hitches for 2012 Subaru Legacy Use Same Bolt Holes
• If you have a Curt or a Draw-Tite/Hidden Hitch, the bolt holes will remain the same if you stick with the same brand hitch. In other words, if you have the # C13158 Curt Class III hitch, and you decide to go with the Curt Class II, part # C12298, the holes will match up and you won't need to drill additional holes. All the Hidden Hitch and Draw-Tite Class II and III hitches used the same holes.
  view full answer...


• Fascia Trimming for EcoHitch Hidden Trailer Hitch Receiver on 2019 Subaru Legacy
• There is just a bit of fascia trimming required on your 2019 Subaru Legacy in order to install the EcoHitch Hidden Trailer Hitch Receiver # 306-X7384. What that means is you'll simply snip off part of the bumper fascia in order to give the receiver the ability to jut out from the bumper so you can use your bike rack. I have added a photo which shows the small section you need to cut out. While we don't have any affiliation with installers, any local (or even mobile) mechanic will be...
  view full answer...


• Installing and Removing SilentACT Anti-Rattle Trailer Hitch Receiver Lock
• It is actually not all that difficult to install or remove the Let's Go Aero anti-rattle hitch pin # SHP2082. In most cases you can reach in with a finger and pull out the spring and block portion. Otherwise a screwdriver would have short work of reaching in and pulling out the spring and block. I have linked a video to a product that uses the same system and you can see that installing it is easy. What I do usually to take out the spring and block is to use the pin part or something...
  view full answer...


• Where Does Converter Box of Curt C79CR Mount on 2022 Subaru Legacy
• The instructions for the Curt trailer wiring harness part # C97CR are a little unclear but basically the box does not get mounted inside the vehicle and instead mounts behind the bumper which you can see pointed out in step 7.
  view full answer...


• Trailer Hitch Installation for a 2014 Subaru Legacy
• The installation of the Draw-Tite # 75673 that you referenced that has been confirmed to fit your 2014 Subaru wouldn't be too difficult but I can understand wanting to have someone else install the hitch for you. However, check out the video link I attached to the right. It shows exactly how this hitch will install on a very similar Legacy as yours. Any qualified mechanic with a good reputation in your area would have no problem installing this hitch. Compared to what they normally do...
  view full answer...


• Replacing Factory Side Mirror on 1996 Subaru Legacy
• We haven't gotten a chance to replace the mirrors on a Subaru Legacy so we don't have an install video available at this time. With that being said when replacing the driver's side mirror with the K-Source # KS71504U you will just need to first remove the interior trim panel with the door open. It will be held on with clips so it should just be a matter of getting a good grip on the sides and pulling it off, carefully undoing each of the clips in the process until the entire piece comes...
  view full answer...


• Installation Instructions for EcoHitch 306-X7271 for Subaru Legacy
• Congrats on your purchase! We typically include a link to the installation instructions in each hitch product page but since EcoHitch does not provide a link to the installation instructions on their website, we're not able to provide one on ours. Your EcoHitch # 306-X7271 (confirmed to fit all models of the 2015 Subaru Legacy) will definitely include a hard copy of the complete installation instructions but I have attached snips of the written portion of the digital instructions. That...
  view full answer...


• Installation Of SportRack Semi-Custom Roof Rack On 2003 Subaru Legacy
• When you are installing the roof rack it is really important you follow the installation instructions in order to get a good fit. I spoke with a couple of our installers and they told me they have to shift the rack a little to get it to fit just right. Per the instructions I saw you need to set the width for the feet at 32. If the feet are adjustable you may be able to move them a bit by using the main screw for the feet. Then, measuring from the center line between the door post and...
  view full answer...


• Installing Prodigy P2 Trailer Brake Controller # 90885 in 2011 Subaru Legacy Sedan
• First, thank you for your recent purchases from etrailer. I'd first suggest a cautionary check of your Legacy owner's manual to confirm its towing capacity. Not all versions of any given year and model vehicle will necessarily share the same capacities. Towing a vehicle safely means having enough engine power, transmission cooler capacity as well as braking performance. If your trailer is large enough to need electric brakes, you definitely want to make certain that the vehicle itself...
  view full answer...


• Is Trimming Required To Install EcoHitch Trailer Hitch EH36RR on 2023 Subaru Legacy?
• All models of the 2023 Subaru Legacy will require minor trimming to get the EcoHitch # EH36RR installed. This is not limited to EcoHitch and instead is required for every hitch that fits your vehicle. I went ahead and included a cutout from the instructions that show where you'll need to trim.
  view full answer...