bing tracking image

Filter Questions and Answers:

reset filter

Expert Answers about Nissan


  • Run Time Per Tank of Gas for Etrailer Portable Inverter Generators Run in Parallel
  • The etrailer 4,900-Watt Portable Inverter Generators - 4,275 Running Watts - Gas - Manual # 333-0001-0002 will run for 4-6 hours at that 2,500 watts running load. That is with the generators in regular mode. You may get a little more time using Eco mode but that Eco mode is the biggest help with smaller loads under 25% not the 58% you stated. In general, when running in parallel without the eco mode you will get 8-9 hours at 25% capacity and 4-6 hours at 50% capacity. The Eco mode will...
    view full answer...

  • Does Included 6-Way Connector Bracket Mount Directly to Tabless Base Plate # DM9519339
  • I spoke with my contact at Demco and the 6-Way connector bracket that is included with the Demco Tabless Base Plate Kit # DM9519339 referenced in your question isn't really designed to mount to the base plates themselves. The bracket is a universal piece that will simply get mounted to a flat surface in a convenient location on your Jeep. Because vehicles greatly differ depending on various packages and models, there aren't any specific instructions as to how and where the bracket should...
    view full answer...

  • Does Skid Plate of 2016 Toyota Tundra Need to be Modified to Install Front Hitch
  • There is a 4 inch diameter hole that needs to be cut in the skid shield of your 2016 Toyota Tundra to be able to install the Draw Tite front hitch part # 65080 that you referenced. I attached a diagram that shows where it will be.
    view full answer...

  • Valve Stem Flow Through Sensors for Tire Pressure Management System
  • The Flow Through Tire Sensors for TST TPMS - Qty 2 # TST-507-FT-S2 comes with the nut that fits on the valve stem behind the sensor. This nut and the special wrench will allow you to tighten that nut to the sensor from the back to secure it to your valve stem for increased security. You are correct that the nut and wrench are on the input side of the sensor and not the output so I'll have that photo removed as it is incorrect.
    view full answer...

  • Installing Roadmaster Flexo-Coil Wiring on a 2019 Jeep Wrangler Rubicon JL
  • According to my research you can use the Flexo-Coil Wiring Kit # RM-15267 for your 2019 Jeep Wrangler Rubicon but I don't believe you will connect to the same color wires as shown in the linked video for this kit on a 2017 Wrangler Unlimited. From what I could find I believe that the running light should be a white and gray wire on your driver's side but a white and orange wire on the passenger side. The stop/turn signals should be found on the yellow wire for the driver's side and the...
    view full answer...

  • How to Discourage Theft of B&W Companion 5th Wheel Hitch
  • Locks are primarily deterrents to theft. No lock on any given product can absolutely prevent theft, and just as you say with enough time and the correct tools a nasty person could steal just about anything. If your pickup were parked unguarded for a long time a thief might instead steal your truck wheels since they at least can be rolled! The handles on the B&W Companion # BWRVK3670 base can be locked
    view full answer...

  • Trimming Fascia on 2017 Ford Fusion Energi to Install Draw-Tite Receiver Hitch # 24897
  • When installing the Draw-Tite Class I Receiver Hitch # 24897 on your 2017 Ford Fusion Energi (along with the other hitch models available for this vehicle) you will indeed want to trim the rear fascia instead of removing it completely in order to protect the battery. This really shouldn't add much if any time to the install process as it's just going to take the place of having to remove all of the nuts and screws that would be required to remove the entire panel. The fascia will just...
    view full answer...

  • How to Test for Continuity with Multimeter
  • 7-Function Digital Multimeter # PT89ZR does not have a buzzer or indicator light like the probe circuit tester # PTW2993, which is shown in the linked video. To use this multimeter for continuity testing turn the dial to the position called out by the red arrow in the photo. Another method you can use with a multimeter that does not have a continuity mode is to select the lowest setting in the resistance mode.
    view full answer...

  • How Many Skis Could Yakima EasyTop Rack Carry
  • There isn't a specific ski amount this rack was tested for by Yakima but I'd not recommend trying to carry over two pairs. I attached review video link for this for you to check out as well.
    view full answer...

  • Does Titan T63FR Surge Coupler Include Master Cylinder Caps & Covers
  • Since we have the Titan Aero 7500 Drum Brake Coupler # T63FR in stock I checked our warehouse inventory and YES the master cylinder caps and covers are included. This unit can be manually bled and in a separate email I have sent the instructions.
    view full answer...

  • Where Does EcoHitch Hidden Front Mount Hitch # 306-X7900 Install on 2018 Ram 2500
  • The 2 inch receiver for the EcoHitch Hidden Front Mount Trailer Hitch # 306-X7900 referenced in your question will actually protrude through the grille of your truck. This allows for a really clean appearance while also maintaining your existing ground clearance. I have attached an image of the hitch installed that you can take a look at as well. If present the factory tow hooks will need to be removed during installation. This front mount hitch features a 7500 pound line pull rating...
    view full answer...

  • Installation of B&W Turn Over Ball Gooseneck BWGNRK1012 in 2011 Silverado
  • The B&W Turn Over Ball Gooseneck hitch # BWGNRK1012 that you referenced fits the 2011 Silverado 2500 and 3500, both long beds and 6-1/2-foot beds. Of course it also fits the equivalent Sierras. The linked instructions on page 2 give you the hitch positioning for each bed length. The hitch ball hole position is referenced to the rear edge of bed. You can also refer to the linked diagram taken from those instructions that gives the two dimensions depending on your bed length. If you need...
    view full answer...

  • Is Relocation Sensor Really Needed for Hands Free Liftgate on 2018 Honda CR-V Trailer Hitch Install
  • When installing a trailer hitch on a 2018 Honda CR-V like the Draw Tite part # 76128 that you referenced Honda states that the hands free liftgate will be blocked and they do offer a relocation harness for this as the Power Liftgate Sensor Relocation Bracket as part # 08U59-TLA-100A which you'd have to get through them. That said, we've also had a few customer come back and say they were still able to operate the hands free liftgate without the harness. They just had to be very specific...
    view full answer...

  • Will Roadmaster Diode Wiring Kit # RM-15267 Work on Towed Vehicle with Battery Disconnected
  • Yes, the Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit # RM-15267 will work perfectly on your 2010 Smart fortwo that requires the battery to be disconnected when being flat towed. The power that activates the signal lights on the fortwo will be coming from the RV so the battery being disconnected is not a problem. Since the battery does need to be disconnected I recommend adding the Roadmaster Automatic Battery Disconnect with Switch # RM-766 to your setup. This will install...
    view full answer...

  • How to Remove Access Panel and Install a Brake Controller on a 2018 GMC Acadia
  • Your 2018 GMC Acadia actually has blunt cut wires for you to splice in a brake controller like the Tekonsha Prodigy P3 # 90195. The last Acadia to use the Adapter # 3026-P that you referenced was the 2017 Limited which was the same as the 2016 model year. The 2017 New Body and newer have the blunt cut wires up under the dash. I took a look at the online version of the owner's manual for your 2018 Acadia and on page 278 it says that the blunt cut wires can be found above the parking brake...
    view full answer...

  • How to Connect 7-Way to Blunt Cut OEM Wires on a 2017 Ram 3500
  • I checked the online version of the owner's manual for your 2017 Ram 3500 and the only thing that it stated in regards to trailer wiring is that it is already run. Because of this and the picture you sent in it looks like someone may have modified the wiring on your Ram. I can give you some pointers on how to install a 7-Way but unfortunately I don't know what color wire is for what function in your picture. What I recommend doing is installing a universal wiring connector like the Hopkins...
    view full answer...

  • Pivoting of Head on Curt E16 5th Wheel Head
  • The Curt E16 5th Wheel Trailer Hitch w/ R16 Roller - Slide Bar Jaw - 16,000 lbs # 16516 will pivot side to side and front to back. This allows you to connect and disconnect on slightly unlevel ground. I've attached a couple videos to assist with the visual.
    view full answer...

  • What Does the Amp Rating of the 25 Amp Progressive Dynamics Inteli-Power RV Converter Represent
  • In regards to the Progressive Dynamics Inteli-Power RV Converter and Smart Battery Charger part # PD922524, the 25 amp rating is both the total amperage the converter can put out and how many amps per hour it can charge.
    view full answer...

  • How Does Happijac Camper Jack Attach to Camper
  • On the camper you'd have a set of the Happijac Z-brackets like part # LC182493 installed which is what the jacks like part # LC736514-4 attach to.
    view full answer...

  • Troubleshooting Difficult to Thread in Hitch Install Bolts
  • Trailer frame weld nuts notoriously end up with rust in them which makes installing hitch hardware pretty difficult. Often times it seems like the solution is to use smaller hitch hardware but the real solution is to clean out the weld nuts so that the hardware can fit like it needs to. I have included a few links on hitch installation tips, cleaning weld nuts, and a video on cleaning weld nuts for you. Typically the most efficient solution is to get a thread tap to clean the weld nuts.
    view full answer...