Expert Answers about Ford Edge
- Availability of Locking Hitch Pin for Yakima Roc 4 Bike Rack
- For a replacement hitch bolt that is confirmed to work with your Yakima Roc 4 Bike Rack, I recommend the part # Y8890200. This threaded bolt is designed for the shank on your existing rack and includes the washer and clip. Then, to lock the hitch bolt and secure the carrier to your vehicle, I recommend adding the Yakima HitchLock # Y07235. This will attach over the hitch bolt and uses the included locking core and key to secure it into place. There is not an all-in-one locking hitch pin...
view full answer... - Replacement Hardware for Trailer Hitch Receiver on 2014 Ford Edge
- For replacement hardware for the etrailer Trailer Hitch Receiver # e98870, and other hitches for the 2014 Ford Edge, you need the Replacement Hardware Kit for Trailer Hitches # RHK. Enter the item number in the open field labeled "Hitch Item Number" and click add to cart. The price can be found on the product page.
view full answer... - Replacement Door Assembly for Yakima BaseLine Towers
- I do believe we've got the part you're looking for with the Replacement Door Assembly for Yakima BaseLine Towers - Qty 1 # 8880620, which is the plastic cover for the BaseLine towers. I've also listed a few other potential replacement parts if that's not the one you're seeking that you may want to check out.
Replacement Swing Door for Yakima BaseLine Towers - Qty 1 # 8880621
or
Replacement Rubber Topper for Yakima BaseLine Towers - Qty 1 # 8880619
If these aren't the parts you're seeking...
view full answer... - How to Get Replacement Arms for Roadmaster Base Plates on 2012 Ford Edge
- You can get replacement arms for the Roadmaster EZ Base Plate Kit # 524426-1 on your 2012 Ford Edge with the Roadmaster Replacement Arms for Base Plate Kits # RM-ARMS.
There will be a link titled "Installation Details" on the product page which you have to click on that will allow you to order the new arms.
As for the tow bar you mentioned, the correct part is the Roadmaster Falcon 2 Tow Bar # RM-520.
I'm not sure what other parts you were referring to by "tow bar package" but apart...
view full answer... - Brake Controller and 7-Way Recommendation for 2021 Ford Edge Titanium with Tow Package
- Since you have a 4-way trailer wiring harness now installed on your 2021 Ford Edge Titanium since you have the tow package you will need to convert it to a 7-way with the Brake Controller Install Kit part # ETBC7 which also comes with everything needed to wire in a brake controller.
For a brake controller I really like the Brake EVN part # TK63VR which senses how hard you are applying the vehicle brakes and applies the same amount to your trailer brakes.
view full answer... - Replacement Shank and Support Bar for a Roadmaster Falcon All Terrain Tow Bar
- The front end of the Falcon All Terrain tow bar, # RM-522, is # 910019-20. This is the part that fits in the actual hitch on the tow vehicle.
If you are talking about the bar at the other end that fits between the 2 tow bar arms and attaches to the vehicle that you are towing, it is # 910021-00.
view full answer... - Screen Door Replacement For A Bounder RV
- The closest screen door slider available is the Lippert Motor Home Entry Screen Door Bubble Slider Panel - Frosted Item # LC234101. It measures 12" x 12" x 1-3/16".
view full answer... - Replacement Yoke Bolt and Bushing for a Roadmaster Falcon 2 Tow Bar
- It sounds like you need bolt # RM-350184-50 and the bushing # RM-200029-10. We have several other replacement parts for the Roadmaster Falcon tow bars and other tow bars. I have included a link to the replacement parts we have for the Falcon 2 tow bar. If you have a different tow bar let me know what it is and I can determine what parts we have for it.
view full answer... - Replacement Motor For Coach Electric Steps
- The Coach Steps are made by Lippert Components. For your motor, you will need the Replacement Motor for Lippert Electric Coach Step # LC301695. This will replace the motor you mentioned but you will want to keep the 3 installation bolts from your old motor as they are not included with this replacement.
view full answer... - Replacement Roadmaster Quick Disconnects for a Sterling All Terrain Tow Bar
- It looks like you have a car side in the picture. You can get a set of replacements using # RM-222. I would recommend replacing both so they wear the same. And for reference the tow bar side is # RM-221. The individual left and right sides are not available by themselves.
view full answer... - Bearing Kit for Dexter D28H Axle on Calkins Trailer
- A Dexter D28H axle is rated for 2800-lbs and its spindle requires a hub that uses inner bearing # L68149 and outer bearing # L44649. For a bearing kit you can use # BK2-100.
These are the same bearings used in the hub/drum # 84546UC3-EZ that you referenced. This hub is rated for 3500-lb axles.
view full answer... - Replacement Gear for Kwikee Steps 9010000220 On Fleetwood Bounder Motorhome
- It sounds like you are going to need either the Replacement Motor for Kwikee Electric RV Steps part # LC379147 or the Replacement Gear Box and A Linkage part # LC379160. I spoke with Lippert and was able to cross reference the info provided so I can confirm these are the correct parts. In order to determine which exact component is creating the noise, I recommend isolating each (unhooking shaft from motor and applying power etc). as that would then give you your answer.
Please note, depending...
view full answer... - 2 inch Hitch Recommendation for a 2012 Ford Edge that Doesn't Require Rear Bumper Trimming
- The Draw Tite Hitch part # 75992 that you referenced is a confirmed fit for your 2012 Ford Edge non-Sport model. The rear fascia/bumper would not get modified but the heat shield would.
I attached an install video for this hitch for you to check out as well.
view full answer... - Motor Home Side Female Air Line Quick Disconnect for Brakemaster Braking System
- You can get both sides of the quick disconnect for the Brakemaster braking system using part # RM-921004-80. Or for the female end with the L-shaped mounting bracket use # RM-921004-60. Or for just the female fitting use # RM-450710.
view full answer... - Replacement Side Wind Jack Handle for 7000-lbs Square Direct Weld Jack
- You can replace the handle of the Square Direct Weld Jack w/ Footplate - Drop Leg - Sidewind - 28-7/8" Lift - 7,000 lbs # TJD-8000S with the Replacement Sidewind Handle for etrailer and Ram Square, Direct Weld Jacks - 3K - 7K # TJD-7000S-HD.
view full answer... - Parts Needed to Add 7-Way and Brake Controller to 2009 Ford Edge
- You will need to start with a 4-way (if you do not have one). For that you would want the # 118551.
From there you would need to convert the 4-way to a 7-way so that you can install the brake controller. For that you will want the Brake Controller Install Kit and 7-Way Adapter part # ETBC7. I attached installation instructions and an install video for this product as well.
For a brake controller I would recommend the Prodigy P2 Brake Controller part # 90885. This is our best selling brake...
view full answer... - Replacement Key for Sears Sport 20-SV With A108 Lock Core
- What you need is the # THKEYN108. This is the correct replacement key for your A108 lock core on your Sears Sport 20-SV.
view full answer... - Replacement Parts for Blue Ox Aventa LX BX7445 Tow Bar
- We do have replacement parts available for the Blue Ox Aventa LX Tow Bar model BX7445 that you mentioned but not a complete rebuild kit. The available replacement parts are as follows:
Machined Hold Up Bolt # BX229-0436
Latch Handle Grips # BX84-0181
Replacement Clip # BX2290794
view full answer... - Replacement Inner Member Of Dexter DX7.5L A-60 Brake Actuator
- We do carry the Replacement Inner Member # DX99FR that fit the Dexter DX7.5L A-60 Brake Actuator # DX56FR and Legacy UFP brake actuators. This would allow you to replace just the inner portion of your current actuator as long as yours is one of the above actuators.
view full answer... - Replacement Hardware Kit for Trailer Hitches
- We do have a replacement hardware kit for your hitch. You will need the Replacement Hardware Kit for Trailer Hitches # RHK.
Make sure that in the pull down menus (below the Shipping Special box) you insert your hitch number, and the manufacturer of the hitch so that you get the correct hardware kit.
Pricing is available once you input all the necessary information.
view full answer...
Go To Results