While this Draw-Tite Trailer Hitch, part # 24767, is mostly out of plain site, it is not completely hidden.
If you want to get an idea of what this hitch looks like installed check out the video I attached below. At this time we do not have any pictures of the hitch installed but you can get a pretty good idea by watching the installation video.
I could not safely recommend that you cut off a portion of the hitch and then bolt back in place when you want to use it. Even though you would... view full answer...
The correct wiring for a 2010 Cadillac CTS is the Tow Ready Custom Fit Vehicle Wiring, # 46255. The connection points for this harness are located behind each of the tail light assemblies. In a sedan, you would pull back the trunk lining to gain access to the back of the tail lights. But on a wagon, either the tail light assemblies will need to be removed or there may be an access panel in the cargo area that needs to be taken off in order to reach the connection points.
I have included... view full answer...
The best place to mount the Derale Transmission Cooler # D13502 on your 2006 Cadillac CTS is directly behind the front grill and in front of the radiator and A/C condenser. It looks like you will have to remove the front grille or at least the core support cover in order to get an accurate available space measurement. In the attached picture you will see the different spaces that a transmission cooler can install, which in your case # 1 would work best if there is enough available space.
If... view full answer...
To get the Curt Trailer Hitch # C11196 installed on your 2013 Cadillac CTS, you may need to enlarge an access hole on both sides of the frame to get the spacers to fit. This does happen some times due to variances in the manufacturing processes. Typically a rotary tool or drill can be used to accomplish this. We do not have an install video for this application as of yet, but I did include a hitch installation we did on a 2013 Subaru that shows an easy way to expand an access hole. If you... view full answer...
According to the installation instructions for the CURT Trailer Hitch # C11307, there is no trimming required on a 2005 Cadillac CTS. I have included a link to the installation instructions for you.
If you are planning on doing some towing, this hitch comes with the correct ball mount, hitch pin and clip. For a ball you can use # 19256 (1-7/8 inch diameter) or # 19258 (2 inch diameter). For trailer wiring use Curt Vehicle Wiring Harness, # C59236. I have included a link to the installation... view full answer...
I don't have specific written instructions for the # C59496 to get installed on your 2012 Lincoln MKZ, because it is a universal kit. I attached a couple of videos on different vehicles to give you a general idea of the install, but I don't have one for an MKZ. view full answer...
According to the installation details of the Draw-Tite Sportframe Trailer Hitch Receiver # 24767 (Which I've linked) it will fit your 2004 Cadillac CTS-V without any fascia trimming. It is stated that since you have dual exhaust it will be a tight fit to get the hitch in place while installing. view full answer...
Once the pads are in place on the Inno Kayak Carrier #INA455, you can leave them installed so you have the right fit for next time. view full answer...
I spoke with my contact at Dutton-Lainson about the Two Speed Hand Winch, part # DL14881. They told me that this does freewheel when disengaged and the handle will turn as the cable is extended.
We do offer a replacement 3-1/8 inch drum that will fit the 3,500 lb Dutton-Lainson hand winches. The part number for this part is # DL304161-BK. view full answer...
Yes, you will need to drill 4 holes in the trunk pan. YOu will use a 1/8 inch drill bit to start the holes then enlarge them using a 1/2 inch bit. I would use some sort of silicone sealant to seal the holes as well.
I have added a link to the instructions below for you to review. view full answer...
The Optronics Thinline Submersible Red LED Clearance and Side Marker Light # AL91RB installs using a base, part # A91BOB in black or part # A91OB in chrome finish. A 2-wire pigtail # A46PB will allow for electrical installation. The white wire on the pigtail is ground.
If your original light used only 1 wire then its base provided the ground connection. In this case you can use the self-grounding base # A91BB in black or # A91CB in chrome finish. In this case you will use Single Wire #... view full answer...
Yes, the Redline Mini Thinline Clearance or Side Marker Light # LT02-230 is submersible. It features a sonically sealed lens and housing so it is waterproof. I have linked a video review of this light below. view full answer...
You can use the Rhino Rack Load Stops # RRRLH2, which fit the Malone AirFlow2 crossbars on the Malone AirFlow Roof Rack # MPG216. I'd use these paired with some straps like the etrailer Cam Buckle Cinch Straps w/ Buckle Protectors - 1" x 13' - 293 lbs - Qty 4 # E98876-4, which would allow you to put some sheets of plywood on the rack for transport. view full answer...
I have exactly what you are looking for. I have attached a video of a etrailer Trailer Hitch Receiver # e62AR on a 2017 Cadillac XT5. view full answer...