Expert Answers about Mazda 5 install

Expert Answers about Mazda 5

Will I need to Drill the Frame on a 2010 Mazda 5 to Install Draw-Tite Hitch 24773
Draw-Tite hitch 24773 for your 2010 Mazda 5 does not require you to drill new holes, but you will need to enlarge two existing holes with a 1/2 inch drill bit. This is a much easier task than measuring for and drilling new holes. I have added a link to the instructions that come with the hitch for you to review.
view full answer...

Installation of the Lets Go Aero Anti-Rattle Trailer Hitch Receiver Lock
The SilentACT Anti-Rattle Trailer Hitch Lock - 1-1/4" and 2" Hitches # SHP2082 is designed to be used with a ball mount or other accessory. The bike racks normally have a brand specific anti-rattle locking hitch where the inside of the bike rack shank that goes into your receiver is not hollow and rather is already threaded for that brand pin so you wouldn't need a separate one for another vehicle as most fit 1-1/4 and 2 inch hitches. There are a few bike racks that do not have a threaded...
view full answer...

Using Curt Bike Rack Strap Part # 18050 to Help with Bike Rack Bounce on a 2010 Mazda 5
Although the Kuat Alpha has a 3 bike capacity, when it is used with a class I receiver such as the one on your Mazda, you should only place 2 bikes on it. This is not only due to the limited tongue weight capacity of the hitch, but also because of the increased leverage placed on the receiver. When loading the bikes on the rack, make sure the heaviest bike is placed closest to the vehicle. The Curt Bike Rack Strap you referenced, part # 18050 would be an excellent choice for providing...
view full answer...

Will Installation Video for Draw-Tite Hitch # 24874 Apply to Hidden Hitch # 60291
Yes! The two hitches you referenced that fit your 2012 Mazda 5, Draw-Tite Hitch # 24874 and Hidden Hitch # 60291 (no longer available), both install in exactly the same location on your car and the install video for the Draw-Tite will apply equally to the Hidden Hitch # 60291. Draw-Tite and Hidden Hitch are in fact sister brands that are both part of the Cequent Group. I have linked the install video for you, as well as two helpful articles with hitch installation tips. This hitch is...
view full answer...

How to Install a Roof Rack on a 2017 Mazda 5 with a Naked Roof
Take a look at the video I attached of the Yakima roof rack system being installed on a 2013 Mazda 5. About 20 seconds in you see the installer remove the black covers along the strips on the roof. Under these covers are mounting points for the roof rack to fasten to. The Yakima system that fits your 2017 Mazda and is similar to the system in the video consists of the 48 inch round bars # Y00408, SkyLine towers # Y53TR, adapters # Y03536, and landing pads # Y00248. This is my favoite...
view full answer...

How to Enlarge Access Holes to Install Curt Hitch # C11127 on a 2012 Mazda 5 w/o Die Grinder
Actually there are drill bits made for power drills that will work just like a die grinder. So I would recommend you get one of those drill bits and then use it with your drill to enlarge the access holes of your 2012 Mazda 5 to install the Curt Hitch # C11127. I attached a link to the installation instructions for this product for you to check out also.
view full answer...

Explanation of Why Class II Hitch Cargo Carrier Wont Fit Class I Hitch
The nub you mentioned is actually there intentionally to prevent what you are trying to do as annoying as that sounds. You see there are Class I and Class II hitches that are 1-1/4 inch sized like what you have. The difference is Class II has higher capacities than the very low capacity Class I hitch. So to prevent Class II only accessories from being used in a Class I hitch they put that nub in the hitch and then only Class I hitch accessories have a cut out portion in the shank which...
view full answer...

Installation Mounting Question for the Whispbar Crossbar System # WB-S24 on a 2013 Mazda 5
The picture that you reference is actually just being used to demonstrate approximately how the bars would look on your vehicle. You are correct, the Whispbar Roof Rack # WB-S24 when installed on your Mazda 5 will be using a screw and mounting plate what attaches to your factory fixed mounting points. The clips that I noted in the picture, that you are questioning, are used on other vehicles that do use these crossbars in a removable situation. By installing these bars you have a many...
view full answer...

Mounting Hole Enlargement to Install Draw-Tite Class I # 24874 on 2012 Mazda 5
The instructions for the Draw-Tite Class I receiver specify that on the passenger side frame rail the front-most attachment hole needs to be enlarged slightly. As an alternate, a 1 inch diameter hole can be drilled in the bottom of the frame member as shown in the diagram I provided. No drilling or enlarging will be required on the drivers side. You can see the installation instructions by clicking the provided link.
view full answer...

Why It Is Not Recommended to Carry More Than 2 Bikes with a Class 1 Hitch
When you carry more than two bikes it becomes more an issue of leverage of the weight than it does overall weight. That third bike may not weigh much, but since that additional weight will be at such a far distance from the hitch pin hole that weight will apply a lot of leveraged torque on the Class I hitch that can not handle the force and could potentially damage hitch/frame of your vehicle. That is why if you install this Draw-Tite Sportframe Trailer Hitch Receiver # 24773 and plan...
view full answer...

Wiring a Powered Modulite Power Wire and Backup Lights on a 2007 Mazda 5 Towing a Trailer
If the dealer hooked up the trailer wiring harness on your vehicle then they must know of a circuit that provides enough amperage to power trailer lighting and not affect the vehicle wiring in any way, if there is an over draw or short. We recommend that the power wire from the item # C59496, be connected to the vehicle battery positive post to eliminate any chance of damaging the sensitive circuitry on the vehicle. If you need to install a 5-Way adapter, item # 47515, to provide reverse...
view full answer...

Can the Ventline S0721 Series RV Range Hood w/ Light # S0721-24WD-F-1 Be Powered by 120 Volts
We don't sell them, but you will need a converter to take the 120 volt power source and convert it to 12 volts to do this. Once you have one you could easily install the Ventline S0721 Series RV Range Hood w/ Light # S0721-24WD-F-1.
view full answer...

Weight Capacity and Warranty Restrictions for Installing Draw Tite Trailer Hitch 24773 on a Mazda 5
The # 24773 hitch is rated to tow up to 2000 pounds, but this does not necessarily mean your 2009 Mazda 5 is capable of towing this much. You can normally find the vehicle tow capacity in your manual. Installing an aftermarket hitch does sometimes void vehicle warranties, but this would be something you would need to discuss with your dealer. I would recommend using a rust proofing spray or undercoating for the hitch installation. This can be found at your local hardware store. The...
view full answer...

Can You Tie Into the Rear Aux Port For Power When Installing Trailer Harness On a 2007 Mazda 5
The T-One Vehicle Wiring Harness part # 118520 is indeed an excellent option for a 2007 Mazda 5 and rather simple to install or at least straight forward. As mentioned, you need to run the power wire up to the battery. This question gets asked a lot but I can't recommend using the rear auxiliary port as it may not be rated for the amp draw of the harness and sorta defeats the purpose of being a powered kit as you are now relying on the factory wiring so if an issue were to occur you risk...
view full answer...

Where to Place the Stabilization Strap On a 2012 Mazda 5 to Carry a Cargo Carrier with a Curt Hitch
On the vehicle side, you would place the stabilization strap end in the gab between the roof and the rear hatch on the 2012 Mazda 5. The other end of strap # 18050 can be attached to the top rail of the carrier either at the back in the center or at the front if there is space. As long as the strap is relieving some of the stress on the hitch, it is really up to you were you place it.
view full answer...

Trimming or Modification Needed to Install Draw-Tite or Hidden Hitch Trailer Hitch on a 2012 Mazda 5
The installation process for the Draw-Tite Sportframe Trailer Hitch, # 24874, and the Hidden Hitch Trailer Hitch, # 60291 (no longer available), is the same. There is no need to trim, cut or modify any part of your 2012 Mazda 5 other than the access hole to allow room for the spacer and carriage bolt to pass through. I have attached a video of a trailer hitch installation that shows how to enlarge the access hole. The Hidden Hitch trailer hitch includes a ball mount, pin and clip, but...
view full answer...